Abstract: | The present study is mainly concéntrated on the visible fluorescence of Ho3+ ,nd 3+ and Er 3+rare earths in alkaline earth fluoride hosts(caF2,srF2,BaF2) using a nitrogen laser excitation. A nitrogen laser was fabricated and its parametric studies were first carried out. |
Description: | Department of Physics, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/3509 |
Files | Size |
---|---|
Dyuthi-T1459.pdf | (12.02Mb) |
Abstract: | Materials and equipment which fail to achieve the design requirements or projected life due to undetected defects may require expensive repair or early replacement. Such defects may also be the cause of unsafe conditions or catastrophic unexpected failure, and will lead to loss of revenue due to plant shutdown. Non-Destructive Evaluation (NDE) / Non Destructive Testing (NDT) is used for the examination of materials and components without changing or destroying their usefulness. NDT can be applied to each stage of a system’s construction, to monitor the integrity of the system or structure throughout its life. |
URI: | http://dyuthi.cusat.ac.in/purl/13 |
Files | Size |
---|---|
Dyuthi-T0349.pdf | (9.607Mb) |
Abstract: | Photoluminescence (PL) spectroscopy is an optical technique that has emerged successful in the field of semiconductor material and device characterization. This technique is quite a powerful one which gives idea about the defect levels in a material, the band gap of the material, composition as well as material quality. Over the recent years it has received an elevation as a mainstream characterization technique. This thesis is an attempt to characterize each individual layer used in a thin film solar cell with special focus on the electrical properties. This will be highly beneficial from the lab as well as industrial point of view because electrical measurements generally are contact mode measurements which tend to damage the surface. As far as a thin film solar cell is concerned, the constituent layers are the transparent conducting oxide (TCO), absorber layer, buffer layer and top electrode contact. Each layer has a specific role to play and the performance of a solar cell is decided and limited by the quality of each individual layer. Various aspects of PL spectroscopy have been employed for studying compound semiconductor thin films [deposited using chemical spray pyrolysis (CSP)] proposed for solar cell application. This thesis has been structured in to seven chapters |
Description: | Applied Optics Division, Department of Physics, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/3835 |
Files | Size |
---|---|
Dyuthi-T1766.pdf | (5.310Mb) |
Abstract: | The motivatitni for" the present work is from .a project sanctioned by TSRO. The work involved the development of a quick and reliable test procedure using microwaves, for tflue inspection of cured propellant samples and a method to monitor the curing conditions of propellant mix undergoing the curing process.Normal testing CHE the propellant samples involvecuttimg a piece from each carton and testing it for their tensile strength. The values are then compared with standard ones and based on this result the sample isaccepted or rejected. The tensile strength is a measure ofdegree of cure of the propellant mix. But this measurementis a destructive procedure as it involves cutting of the sample. Moreover, it does not guarantee against nonuniform curing due to power failure, hot air-line failure,operator error etc. This necessitated the need for the development of a quick and reliable non-destructive test procedure. |
Description: | Department of Electronics, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/3644 |
Files | Size |
---|---|
Dyuthi-T1632.pdf | (3.168Mb) |
URI: | http://dyuthi.cusat.ac.in/purl/5191 |
Files | Size |
---|---|
Dyuthi T-2226.pdf | (396.2Kb) |
Abstract: | This thesis presents analytical and numerical results from studies based on the multiple quantum well laser rate equation model. We address the problem of controlling chaos produced by direct modulation of laser diodes. We consider the delay feedback control methods for this purpose and study their performance using numerical simulation. Besides the control of chaos, control of other nonlinear effects such as quasiperiodicity and bistability using delay feedback methods are also investigated.A number of secure communication schemes based on synchronization of chaos semiconductor lasers have been successfully demonstrated theoretically and experimentally. The current investigations in these field include the study of practical issues on the implementations of such encryption schemes. We theoretically study the issues such as channel delay, phase mismatch and frequency detuning on the synchronization of chaos in directly modulated laser diodes. It would be helpful for designing and implementing chaotic encryption schemes using synchronization of chaos in modulated semiconductor lasers. |
Description: | International School of Photonics, Cochin university of Science & Technology |
URI: | http://dyuthi.cusat.ac.in/xmlui/purl/2109 |
Files | Size |
---|---|
Dyuthi-T0433.pdf | (2.645Mb) |
Abstract: | In this thesis we have presented some aspects of the nonlinear dynamics of Nd:YAG lasers including synchronization, Hopf bifurcation, chaos control and delay induced multistability.We have chosen diode pumped Nd:YAG laser with intracavity KTP crystal operating with two mode and three mode output as our model system.Different types of orientation for the laser cavity modes were considered to carry out the studies. For laser operating with two mode output we have chosen the modes as having parallel polarization and perpendicular polarization. For laser having three mode output, we have chosen them as two modes polarized parallel to each other while the third mode polarized orthogonal to them. |
Description: | International School of Photonics, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/xmlui/purl/1951 |
Files | Size |
---|---|
Dyuthi-T0434.pdf | (7.186Mb) |
Abstract: | Nonlinear dynamics of laser systems has become an interesting area of research in recent times. Lasers are good examples of nonlinear dissipative systems showing many kinds of nonlinear phenomena such as chaos, multistability and quasiperiodicity. The study of these phenomena in lasers has fundamental scientific importance since the investigations on these effects reveal many interesting features of nonlinear effects in practical systems. Further, the understanding of the instabilities in lasers is helpful in detecting and controlling such effects. Chaos is one of the most interesting phenomena shown by nonlinear deterministic systems. It is found that, like many nonlinear dissipative systems, lasers also show chaos for certain ranges of parameters. Many investigations on laser chaos have been done in the last two decades. The earlier studies in this field were concentrated on the dynamical aspects of laser chaos. However, recent developments in this area mainly belong to the control and synchronization of chaos. A number of attempts have been reported in controlling or suppressing chaos in lasers since lasers are the practical systems aimed to operated in stable or periodic mode. On the other hand, laser chaos has been found to be applicable in high speed secure communication based on synchronization of chaos. Thus, chaos in laser systems has technological importance also. Semiconductor lasers are most applicable in the fields of optical communications among various kinds of laser due to many reasons such as their compactness, reliability modest cost and the opportunity of direct current modulation. They show chaos and other instabilities under various physical conditions such as direct modulation and optical or optoelectronic feedback. It is desirable for semiconductor lasers to have stable and regular operation. Thus, the understanding of chaos and other instabilities in semiconductor lasers and their xi control is highly important in photonics. We address the problem of controlling chaos produced by direct modulation of laser diodes. We consider the delay feedback control methods for this purpose and study their performance using numerical simulation. Besides the control of chaos, control of other nonlinear effects such as quasiperiodicity and bistability using delay feedback methods are also investigated. A number of secure communication schemes based on synchronization of chaos semiconductor lasers have been successfully demonstrated theoretically and experimentally. The current investigations in these field include the study of practical issues on the implementations of such encryption schemes. We theoretically study the issues such as channel delay, phase mismatch and frequency detuning on the synchronization of chaos in directly modulated laser diodes. It would be helpful for designing and implementing chaotic encryption schemes using synchronization of chaos in modulated semiconductor laser |
URI: | http://dyuthi.cusat.ac.in/purl/878 |
Files | Size |
---|---|
Dyuthi-T0190.pdf | (4.782Mb) |
Abstract: | Present thesis has discussed the design and synthesis of polymers suitable for nonlinear optics. Most of the molecules that were studied have shown good nonlinear optical activity. The second order nonlinear optical activity of the polymers was measured experimentally by Kurtz and Perry powder technique. The thesis comprises of eight chapters.The theory of NLO phenomenon and a review about the various nonlinear optical polymers has been discussed in chapter 1. The review has provided a survey of NLO active polymeric materials with a general introduction, which included the principles and the origin of nonlinear optics, and has given emphasis to polymeric materials for nonlinear optics, including guest-host systems, side chain polymers, main chain polymers, crosslinked polymers, chiral polymers etc.Chapter 2 has discussed the stability of the metal incorporated tetrapyrrole molecules, porphyrin, chlorin and bacteriochlorin.Chapter 3 has provided the NLO properties of certain organic molecules by computational tools. The chapter is divided into four parts. The first part has described the nonlinear optical properties of chromophore (D-n-A) and bichromophore (D-n-A-A-n-D) systems, which were separated by methylene spacer, by making use of DPT and semiempirical calculations.Chapter 4: A series of polyurethanes was prepared from cardanol, a renewable resource and a waste of the cashew industry by previously designed bifunctional and multifunctional polymers using quantum theoretical approach.Chapter 5: A series of chiral polyurethanes with main chain bis azo diol groups in the polymer backbone was designed and NLO activity was predicted by ZlNDO/ CV methods.In Chapter 7, polyurethanes were first designed by computational methods and the NLO properties were predicted by correction vector method. The designed bifunctional and multifunctional polyurethanes were synthesized by varying the chiral-achiral diol compositions |
Description: | Department of Applied Chemistry, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/3051 |
Files | Size |
---|---|
Dyuthi-T1025.pdf | (6.633Mb) |
Abstract: | The present work emphasizes the use of chirality as an efficient tool to synthesize new types of second order nonlinear materials. Second harmonic generation efficiency (SHG) is used as a measure of second order nonlinear response. Nonlinear optical properties of polymers have been studied theoretically and experimentally. Polymers were designed theoretically by ab initio and semiempirical calculations. All the polymeric systems have been synthesized by condensation polymerization. Second harmonic generation efficiency of the synthesized systems has been measured experimentally by Kurtz and Perry powder method |
Description: | Department of Applied Chemistry, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/3827 |
Files | Size |
---|---|
Dyuthi-T1758.pdf | (3.490Mb) |
URI: | http://dyuthi.cusat.ac.in/purl/1696 |
Files | Size |
---|---|
Dyuthi-T0226.pdf | (4.359Mb) |
Abstract: | Interfacings of various subjects generate new field ofstudy and research that help in advancing human knowledge. One of the latest of such fields is Neurotechnology, which is an effective amalgamation of neuroscience, physics, biomedical engineering and computational methods. Neurotechnology provides a platform to interact physicist; neurologist and engineers to break methodology and terminology related barriers. Advancements in Computational capability, wider scope of applications in nonlinear dynamics and chaos in complex systems enhanced study of neurodynamics. However there is a need for an effective dialogue among physicists, neurologists and engineers. Application of computer based technology in the field of medicine through signal and image processing, creation of clinical databases for helping clinicians etc are widely acknowledged. Such synergic effects between widely separated disciplines may help in enhancing the effectiveness of existing diagnostic methods. One of the recent methods in this direction is analysis of electroencephalogram with the help of methods in nonlinear dynamics. This thesis is an effort to understand the functional aspects of human brain by studying electroencephalogram. The algorithms and other related methods developed in the present work can be interfaced with a digital EEG machine to unfold the information hidden in the signal. Ultimately this can be used as a diagnostic tool. |
Description: | International School of Photonics, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/3811 |
Files | Size |
---|---|
Dyuthi-T1742.pdf | (2.065Mb) |
URI: | http://dyuthi.cusat.ac.in/purl/5574 |
Files | Size |
---|---|
Dyuthi T-2614.pdf | (32.69Mb) |
Abstract: | So far, in the bivariate set up, the analysis of lifetime (failure time) data with multiple causes of failure is done by treating each cause of failure separately. with failures from other causes considered as independent censoring. This approach is unrealistic in many situations. For example, in the analysis of mortality data on married couples one would be interested to compare the hazards for the same cause of death as well as to check whether death due to one cause is more important for the partners’ risk of death from other causes. In reliability analysis. one often has systems with more than one component and many systems. subsystems and components have more than one cause of failure. Design of high-reliability systems generally requires that the individual system components have extremely high reliability even after long periods of time. Knowledge of the failure behaviour of a component can lead to savings in its cost of production and maintenance and. in some cases, to the preservation of human life. For the purpose of improving reliability. it is necessary to identify the cause of failure down to the component level. By treating each cause of failure separately with failures from other causes considered as independent censoring, the analysis of lifetime data would be incomplete. Motivated by this. we introduce a new approach for the analysis of bivariate competing risk data using the bivariate vector hazard rate of Johnson and Kotz (1975). |
Description: | Department of Statistics, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/3355 |
Files | Size |
---|---|
Dyuthi-T1332.pdf | (1.800Mb) |
Abstract: | The thesis entitled novel 1,3-dipolar cycloaddition reactions of acyclic carbonyl ylides and related chemistry embodies the results of the investigations carried out to explore the reactivity of acyclic carbonyl ylides,generated by the reaction of dicarbomethoxy carbine and aldehydes towards dipolarophiles such as activated styrenes,1,2-and 1,4-quinones. In conclusion ,we have explored the reactivity pattern of acyclic carbonyl ylides derived from dicarbomethoxycarbene and aldehyde towards activated styrenes with a view to develop a stereoselective synthesis of highly substituted tetrahydrofuran derivatives. It was also found that the ylide could be trapped by various 1,2-and 1,4-diones to form dioxolane derivatives. It is noteworthy that the cycloaddition is highly region- and stereoselective. With isatins the ylide preferentially adds to the more electrone deficient carbonyl group making it regiospecific. Hetrocyclic compounds are of pivotal importance in organic chemistry, and enormous efforts have been devoted to develop new methodologies for their synthesis. It is noteworthy in this context that, 1,3-dipolar cycloaddition reaction,otherwise called Huisgen reaction, constitutes one of the most efficient methods for the synthesis of five membered heterocycles. Among the various dipoles, carbonyl ylides have received substiancial attention in recent years largely due to their utility in the synthesis of a wide range of oxygen hetrocycles, which are often found as structural subunits of many bioactive natural products. |
URI: | http://dyuthi.cusat.ac.in/purl/953 |
Files | Size |
---|---|
Dyuthi-T0220.pdf | (2.159Mb) |
Abstract: | Burgess reagent first prepared by E. M. Burgess in 1968, is a mild and selective dehydrating agent for secondary and tertiary alcohols and due to the amphipolar nature it is gainfully employed in a number of creative synthetic ventures. A close examination of the structure of Burgess reagent reveals that it can act as a 1,2-dipole. To the best of our knowledge, no attempts have been made to tap full synthetic potential of the amphipolar nature of this reagent and no reports on 1,3-dipolar addition to a σ-bond in acyclic systems are available in literature. In this context, we propose to unravel novel applications of Burgess reagent based on its amphipolar nature. Rich and multifaceted chemistry of nitrones form the basis of many successful chemical transformations used in attractive synthetic strategies. For the last 50 years special attention has been given to nitrones due to their successful application as building blocks in the synthesis of various natural and biologically active compounds. Our interest in nitrones stems out of its unique character: i.e. it is a 1,3-dipole exhibiting distinct nucleophilic activity. We reasoned that 1,3-dipole possessing significant nucleophilicity should react with amphipolar Burgess reagent with elimination of triethylamine to give the corresponding five-membered ring product by formal dipolar addition to a σ bond. To test this hypothesis we studied the reaction of nitrones with Burgess reagent. This thesis reveals our attempts to explore the [3+2] annulation reaction of nitrones with Burgess reagent which was found to be followed by a rearrangementinvolving C-to-N aryl migration, ultimately resulting in diarylamines and carbamates. We have also examined the reaction of cyanuric chloride with nitrones in DMF with a view to exploit the nucleophilicty of nitrones and to unravel the migratory aptitude, if any, observed in this reaction |
Description: | Department of Applied Chemistry, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/4710 |
Files | Size |
---|---|
Dyuthi-T1832.pdf | (1.789Mb) |
Abstract: | The aim of the investigation is to develop new high performance adhesive systems based on neoprene-phenolic blends. Initially the effect of addition of all possible ingredients like fillers, adhesion promoters, curing agents and their optimum compositions to neoprene solution is investigated. The phenolic resin used is a copolymer of phenol-cardanolformaldehyde prepared in the laboratory. The optimum ratio between phenol and cardanol that gives the maximum bond strength in metal-metal, rubber-rubber and rubber-metal specimens has been identified. Further the ratio between total phenols and formaldehyde is also optimised. The above adhesive system is further modified by the addition of epoxidized phenolic novolacs. For this purpose, phenolic novolac resins are prepared in different stoichiometric ratios and are subsequently epoxidized. The effectiveness of the adhesive for bonding different metal and rubber substrates is another part of the study. To study the ageing behaviour, different bonded specimens are exposed to high temperature, hot water and salt water and adhesive properties have been evaluated. The synthesized resins have been characterized by FTIR , HNMR spectroscopy. The molecular weights of the resins have been obtained by GPC. Thermogravimetric analysis and differential scanning calorimetry are used to study the thermal properties. The fractured surface analysis is studied by scanning electron microscopy. The study has brought to light the influence of phenol/ formaldehyde stoichiometric ratio, addition of cardanol (a renewable resource), adhesion promoters and suitability of the adhesive for different substrates and the age resistance of adhesive joints among other things. |
Description: | Department of Polymer Science and Rubber Technology,Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/2541 |
Files | Size |
---|---|
Dyuthi-T0685.pdf | (7.978Mb) |
Abstract: | This research project aims at developing new applications for CNSL in the polymer field. Cashew nut shell liquid (CNSL) is a cheap agro-byproduct and renewable resource which consists mainly of substituted phenols. By using CNSL in place of phenol, phenol derived from petrochemicals can be conserved and a cheap agro-byproduct utilized.In this study CNSL based resin is prepared by condensing a mixture of phenol and CNSL with hexamethylenetetramine and the effect of P: F ratio and CNSL: P ratio on the properties of synthesized resin is studied. The adhesive properties of CNSL based resin in combination with neoprene rubber are investigated. The effect of varying the stoichiometric ratios between total phenol and formaldehyde and CNSL and phenol of the resin, resin content, choice and extent of fillers and adhesion promoters in the adhesive formulation are studied. The effect of resin on the ageing properties of various elastomers is also studied by following changes in tensile strength, elongation at break, modulus, tear strength, swelling index and acetone soluble matter. Crude CNSL and resins with different P: F ratios and CNSL: P ratios are incorporated into elastomers. Lastly, utility of CNSL based resin as binder for making particleboard is investigated.The results show that CNSL based resin is an effective ingredient in adhesives for bonding aluminium to aluminium. The resin used for adhesive fonnulation gives the best performance at 45 to 55 phr resin and a total phenol: formaldehyde of l:2.9. The resin when added at a rate of l5 phr improves ageing characteristics of elastomers with respect to mechanical properties. The reaction mixture of CNSL and hexa and the resin resulting from the condensation of CN SL, phenol and hexa can be used as effective binders for moulding particleboard. |
Description: | Department of Polymer Science and Rubber Technology, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/2926 |
Files | Size |
---|---|
Dyuthi-T0917.pdf | (8.725Mb) |
Abstract: | Biodegradable polymers have opened an emerging area of great interest because they are the ultimate solution for the disposal problems of synthetic polymers used for short time applications in the environmental and biomedical field. The biodegradable polymers available until recently have a number of limitations in terms of strength and dimensional stability. Most of them have processing problems and are also very expensive. Recent developments in biodegradable polymers show that monomers and polymers obtained from renewable resources are important owing to their inherent biodegradability, biocompatibility and easy availability. The present study is, therefore, mostly concemed with the utilization of renewable resources by effecting chemical modification/copolymerization on existing synthetic polymers/natural polymers for introducing better biodegradability and material properties.The thesis describes multiple approaches in the design of new biodegradable polymers: (1) Chemical modification of an existing nonbiodegradable polymer, polyethylene, by anchoring monosaccharides after functionalization to introduce biodegradability. (2) Copolymerization of an existing biodegradable polymer, polylactide, with suitable monomers and/or polymers to tailor their properties to suit the emerging requirements such as (2a) graft copolymerization of lactide onto chitosan to get controlled solvation and biodegradability and (2b) copolymerization of polylactide with cycloaliphatic amide segments to improve upon the thermal properties and processability. |
URI: | http://dyuthi.cusat.ac.in/purl/2894 |
Files | Size |
---|---|
Dyuthi-T0891.pdf | (7.045Mb) |
URI: | http://dyuthi.cusat.ac.in/purl/5140 |
Files | Size |
---|---|
Dyuthi-T2174.pdf | (23.33Mb) |
URI: | http://dyuthi.cusat.ac.in/purl/2969 |
Files | Size |
---|---|
Dyuthi-T0958.pdf | (3.057Mb) |
URI: | http://dyuthi.cusat.ac.in/purl/5435 |
Files | Size |
---|---|
Dyuthi T-2476.pdf | (8.896Mb) |
Abstract: | There is an enormous demand for chemical sensors in many areas and disciplines including chemistry, biology, clinical analysis, environmental science. Chemical sensing refers to the continuous monitoring of the presence of chemical species and is a rapidly developing field of science and technology. They are analytical devices which transform chemical information generating from a reaction of the analyte into an measurable signal. Due to their high selectivity, sensitivity, fast response and low cost, electrochemical and fluorescent sensors have attracted great interest among the researchers in various fields. Development of four electrochemical sensors and three fluorescent sensors for food additives and neurotransmitters are presented in the thesis. Based on the excellent properties of multi walled carbon nanotube (MWCNT), poly (L-cysteine) and gold nanoparticles (AuNP) four voltammetric sensors were developed for various food additives like propyl gallate, allura red and sunset yellow. Nanosized fluorescent probes including gold nanoclusters (AuNCs) and CdS quantum dots (QDs) were used for the fluorescent sensing of butylated hydroxyanisole, dopamine and norepinephrine. A total of seven sensors including four electrochemical sensors and three fluorescence sensors have been developed for food additives and neurotransmitters. |
Description: | Department of Applied Chemistry |
URI: | http://dyuthi.cusat.ac.in/purl/5021 |
Files | Size |
---|---|
Dyuthi-2087.pdf | (11.90Mb) |
URI: | http://dyuthi.cusat.ac.in/purl/4987 |
Files | Size |
---|---|
Dyuthi-T2059.pdf | (3.786Mb) |
Abstract: | The thesis entitled novel heterocyclic constructions mediated by nucleophilic carbenes and related chemistry, embodies the results of the investigations carried out to explore the reactivity patterns of the 1:1 zwitterions, generated in situ from various nucleophilic carbenes and DiMethyl AcetyleneDicarboxylate(DMAD) towards aldehydes and ketones. The traditional synthesis of complex organic molecules employs stepwise formation of bonds and involves multiple steps. Besides the sequential synthesis, in several instances, the desired product can also be obtained in one pot reactions of three or more starting compounds. Such reactions in which more than two starting materials react to form a product in such a way that the majority of the atoms of the starting materials can be found in the products are called multicomponent reactions(MCRs). The results of our investigations on the application of N-heterocyclic carbenes in multicomponent reaction with DMAD and aromatic aldehydes leading to the one pot synthesis of 2-oxy-maleate and furanone derivatives. It is interesting to note that dihydrofuran and lactone motifs are present in a number of biologically active natural products and other heterocyclic compounds. It is conceivable that the novel multicomponent reactions described herein will find application in the synthesis of a variety of heterocyclic compounds, and in natural product synthesis. |
URI: | http://dyuthi.cusat.ac.in/purl/23 |
Files | Size |
---|---|
Dyuthi-T0211.pdf | (2.751Mb) |
Abstract: | This thesis presents the microwave dielectric properties of two novel dielectric resonator materials with the composition Ca(Ca1/4Nb2/4Ti1/4)O3 and Ca(Ca1/4Ta2/4Ti1/4)O3 ceramics and their application in the fabrication of wideband antennas. The microwave dielectric properties of the ceramics were tailored by several techniques such as doping, glass addition and solid solution formations in the complex perovskite A and B-sites with suitable substitutions. Among the wide variety of DRs developed, ceramic resonators with optimum properties were identified to fabricate broadband dielectric resonator loaded microstrip patch antennas. Furthermore, wideband, high permittivity dielectric resonator antennas were fabricated and explored the possibility of tuning their characteristics by modifying the feed line geometries. |
URI: | http://dyuthi.cusat.ac.in/purl/2918 |
Files | Size |
---|---|
Dyuthi-T0909.pdf | (18.00Mb) |
Abstract: | In this introduction part, importance has been given to the elastomeric properties of polyurethanes. Emphasis has been laid to this property based on microphase separation and how this could be modified by modifying the segment lengths, as well as the structure of the segments. Implication was also made on the mechanical and thermal properties of these copolymers based on various analytical methods usually used for characterization of polymers. A brief overview of the challenges faced by the polyurethane chemistry was also done, pointing to the fact that though polyurethane industry is more than 75 years old, still a lot of questions remain unanswered, that too mostly in the synthesis of polyurethanes. A major challenge in this industry is the utilization of more environmental friendly “Green Chemistry Routes” for the synthesis of polyurethanes which are devoid of any isocyanates or harsh solvents.The research work in this thesis was focused to develop non-isocyanate green chemical process for polyurethanes and also self-organize the resultant novel polymers into nano-materials. The thesis was focused on the following three major aspects:(i) Design and development of novel melt transurethane process for polyurethanes under non-isocyanate and solvent free melt condition. (ii) Solvent induced self-organization of the novel cycloaliphatic polyurethanes prepared by the melt transurethane process into microporous templates and nano-sized polymeric hexagons and spheres. (iii) Novel polyurethane-oligophenylenevinylene random block copolymer nano-materials and their photoluminescence properties. The second chapter of the thesis gives an elaborate discussion on the “Novel Melt Transurethane Process ” for the synthesis of polyurethanes under non-isocyanate and solvent free melt condition. The polycondensation reaction was carried out between equimolar amounts of a di-urethane monomer and a diol in the presence of a catalyst under melt condition to produce polyurethanes followed by the removal of low boiling alcohol from equilibrium. The polymers synthesized through this green chemical route were found to be soluble (devoid of any cross links), thermally stable and free from any isocyanate entities. The polymerization reaction was confirmed by various analytical techniques with specific references to the extent of reaction which is the main watchful point for any successful polymerization reaction. The mechanistic aspects of the reaction were another point of consideration for the novel polymerization route which was successfully dealt with by performing various model reactions. Since this route was successful enough in synthesizing polyurethanes with novel structures, they were employed for the solvent induced self-organization which is an important area of research in the polymer world in the present scenario. Chapter three mesmerizes the reader with multitudes of morphologies depending upon the chemical backbone structure of the polyurethane as well as on the nature and amount of various solvents employed for the self-organization tactics. The rationale towards these morphologies-“Hydrogen Bonding ” have been systematically probed by various techniques. These polyurethanes were then tagged with luminescent 0ligo(phenylene vinylene) units and the effects of these OPV blocks on the morphology of the polyurethanes were analyzed in chapter four. These blocks have resulted in the formation of novel “Blue Luminescent Balls” which could find various applications in optoelectronic devices as well as delivery vehicles. |
URI: | http://dyuthi.cusat.ac.in/purl/2928 |
Files | Size |
---|---|
Dyuthi-T0919.pdf | (14.64Mb) |
URI: | http://dyuthi.cusat.ac.in/purl/2924 |
Files | Size |
---|---|
Dyuthi-T0915.pdf | (4.641Mb) |
URI: | http://dyuthi.cusat.ac.in/purl/2797 |
Files | Size |
---|---|
Dyuthi-T0818.pdf | (2.546Mb) |
Abstract: | A systematic investigation of the reactivity and functionalization of two heterocyclic analogs of triphenylmethane , namely tris(2-thienyl)methane and tris(2-furyl)methane have been carried out and the results are presented in this thesis entitled "NOVEL REACTIONS OF TRIS(2-THIENYL)METHANE AND TRIS(2-FURYL)METHANE.". The history of organic free radicals dates back to Gomberg's monumental discovery of the triphenylmethyl radical in 1900. The heterocyclic analogs of triarylmethane are also interesting from the vantage point of their transformation to the corresponding radicals akin to Gomberg ' s triphenylmethyl radical and also they are prone to further transformation leading to three dimensionally elongated molecules such as dendrimers. Dendritic architectures are one of the most pervasive topologies observed in nature at the macro- and microdimensional length devices. Because of their ability to combine both organic and inorganic compounds and their propensity to either encapsulate or be engineered into unimolecular functional devices , dendrimers are versatile amongst existing nanoscale building blocks and materials. |
URI: | http://dyuthi.cusat.ac.in/purl/936 |
Files | Size |
---|---|
Dyuthi-T0219.pdf | (2.339Mb) |
Abstract: | Hindi |
Description: | Department of Hindi,CUSAT |
URI: | http://dyuthi.cusat.ac.in/purl/4764 |
Files | Size |
---|---|
Dyuthi-T1861.pdf | (10.98Mb) |
Abstract: | In the thesis entitled " Novel Strategies for Heterocyclic Constructions via 1 ,4-Dipolar Intermediates"Synthesis of a complex organic molecules essentially involves the formation of carbon-carbon and carbon-heteroatom bonds. Various synthetic methods are available for these processes involving ionic, pericyclic and radical reactions. Among the pericyclic reactions, dipolar cycloaddition reactions, introduced by Huisgen, have emerged as a very powerful tool for heterocyclic construction. Heterocyclic compounds remain an important class of organic molecules due to their natural abundance and remarkable biological activity, thus constituting an intergral part of pharmaceutical industry. In this respect, developing newer synthetic methodology for heterocyclic construction has been an area of immense interest. In recent years, 1,3-dipolar cycloaddition reactions proved to be efficient routes to a wide variety of five membered heterocycles, as attested by their application in the total synthesis of various complex organic molecules. However, the potential application of similar 1,4- dipolar cycloaddition reactions for the construction of six memebered heterocycles remained underexploited. In this context, a systematic investigation of the reactivity of 1,4-dipoles generated from nitrogen heterocycles (pyridine and its analogues) and dimethyl acetylenedicarboxy!ate (DMAD) towards various dipolarophiles has been carried out and the results are embodied. |
URI: | http://dyuthi.cusat.ac.in/purl/929 |
Files | Size |
---|---|
Dyuthi-T0218.pdf | (2.206Mb) |
Abstract: | Carbon-carbon and carbon-heteroatom bond formations constitute the central events in organic synthesis. In view of this, much of the research in organic synthesis has been focused on devising novel and efficient methods for such bond constructions. In general, polar, pericyclic and radical methodologies are employed for this purpose. The polar and radical reactions proceed via reactive intermediates such as carbanions, enols/enolates, enamines, carbocations, radical cations, radical anions, carbenes, zwitterions etc. In recent years, there has been enormous interest in the chemistry of zwitterionic species largely from the standpoint of their applications in multicomponent reactions (MCRs) and organocatalytic reactions. Zwitterions formed by the addition of nucleophiles to electrophilic π-systems such as acetylenic esters and azoesters have been the subject of extensive investigations; their synthetic utility, however, remained largely unexplored. Investigations in a number of laboratories, including our own, have shown that zwitterions of the type mentioned above on reaction with electrophiles give rise to carbo- and heterocyclic products by 1,3- or 1,4-dipolar cycloadditions. Recently, allenoates, another class of active π-systems were introduced to this field. Against this background, a systematic investigation of the reactions of various zwitterions derived from allenoates with different electrophiles especially 1,2-diones, were carried out. The results of these studies are embodied in the thesis entitled “Novel Synthesis of Carbocycles and Heterocycles Employing Zwitterions Derived from Allenic Esters”. |
URI: | http://dyuthi.cusat.ac.in/purl/5090 |
Files | Size |
---|---|
Dyuthi-T 2166.pdf.pdf | (10.03Mb) |
URI: | http://dyuthi.cusat.ac.in/purl/1733 |
Files | Size |
---|---|
Dyuthi-T0228.pdf | (1.948Mb) |
Abstract: | Nitrones or azomethine-N-oxides are important precursors for the synthesis of several heterocyclic systems. They belong to the allyl anion type 1,3-dipoles and possess unique structural features which make them extraordinarily useful synthons. They behave as 1,3-dipoles in 1,3-dipolar cycloaddition reactions and as electrophiles in reactions with organometallic reagents. These are the two basic reactions given by nitrones. Nitrones also act as ‘spin traps’ in which they react with short-lived radicals to furnish stable nitroxide radicals which can be detected and identified by electron paramagnetic resonance (EPR) spectroscopy. Recently SmI2 catalysed reductive cross-coupling reactions of nitrones have gained significant interest in which the reactions are initiated by single electron transfer (SET) to nitrones. Apart from these reactions, nitrones are also known to participate in reactions which are initiated by the nucleophilic attack of nitrone-oxygen. In our group, we have also explored the nucleophilic character of nitrones through various reactions. The results obtained enabled us to develop a novel two-step one-pot strategy for quinolines and indoles - the heterocycles renowned for their pharmacological applications, from nitrones and electron deficient acetylenes. Using dibenzoylacetylene and phenylbenzoylacetylene as dipolarophiles, we could introduce a desired functional group at a predetermined position of the quinolines or indoles to be synthesised. In this context, the thesis entitled “NUCLEOPHILIC ADDITION OF NITRONES TO ELECTRON DEFICIENT ACETYLENES AND RELATED STUDIES” portrays our attempt to expand the scope of our x novel synthetic protocol using ester functionalised acetylenes: dimethyl acetylenedicarboxylate (DMAD) and methyl propiolate. The thesis is organised in to five chapters. The first chapter briefly describes the different classes of reactions that nitrone functionality can tolerate. The research problem is defined at the end of this chapter. The second chapter describes the synthesis of different nitrones used for the present study. The optimisation and expansion of scope of the novel strategy towards quinoline synthesis is discussed in the third chapter. The fourth chapter portrays the synthesis of indole-3-carboxylates using the novel strategy. In the fifth chapter, the reaction of N-(2,6-dimethylphenyl) and N-(2,4,6-trimethylphenyl)nitrones are discussed. Here we also discuss the mechanistic reinvestigation of Baldwin’s proposal in the isoxazoline-oxazoline rearrangement. The major outcome of the work is given at the end of the thesis. The structural formulae, schemes, tables and figures are numbered chapter-wise since each chapter of the thesis is organized as an independent unit. All new compounds (except two compounds reported in fourth chapter) are fully characterised on the basis of spectral and analytical data and single crystal X-ray analysis on representative examples. Relevant references are included at the end of individual chapters. |
URI: | http://dyuthi.cusat.ac.in/purl/5095 |
Files | Size |
---|---|
Dyuthi-T 2161.pdf | (8.455Mb) |
URI: | http://dyuthi.cusat.ac.in/purl/1671 |
Files | Size |
---|---|
Dyuthi-T0224.pdf | (2.570Mb) |
URI: | http://dyuthi.cusat.ac.in/purl/1673 |
Files | Size |
---|---|
Dyuthi-T0225.pdf | (1.674Mb) |
URI: | http://dyuthi.cusat.ac.in/purl/1071 |
Files | Size |
---|---|
Pramood K V 1989.pdf | (175.8Kb) |
Abstract: | Frames are the most widely used structural system for multistorey buildings. A building frame is a three dimensional discrete structure consisting of a number of high rise bays in two directions at right angles to each other in the vertical plane. Multistorey frames are a three dimensional lattice structure which are statically indeterminate. Frames sustain gravity loads and resist lateral forces acting on it. India lies at the north westem end of the Indo-Australian tectonic plate and is identified as an active tectonic area. Under horizontal shaking of the ground, horizontal inertial forces are generated at the floor levels of a multistorey frame. These lateral inertia forces are transferred by the floor slab to the beams, subsequently to the columns and finally to the soil through the foundation system. There are many parameters that affect the response of a structure to ground excitations such as, shape, size and geometry of the structure, type of foundation, soil characteristics etc. The Soil Structure Interaction (SS1) effects refer to the influence of the supporting soil medium on the behavior of the structure when it is subjected to different types of loads. Interaction between the structure and its supporting foundation and soil, which is a complete system, has been modeled with finite elements. Numerical investigations have been carried out on a four bay, twelve storeyed regular multistorey frame considering depth of fixity at ground level, at characteristic depth of pile and at full depth. Soil structure interaction effects have been studied by considering two models for soil viz., discrete and continuum. Linear static analysis has been conducted to study the interaction effects under static load. Free vibration analysis and further shock spectrum analysis has been conducted to study the interaction effects under time dependent loads. The study has been extended to four types of soil viz., laterite, sand, alluvium and layered.The structural responses evaluated in the finite element analysis are bending moment, shear force and axial force for columns, and bending moment and shear force for beams. These responses increase with increase in the founding depth; however these responses show minimal increase beyond the characteristic length of pile. When the soil structure interaction effects are incorporated in the analysis, the aforesaid responses of the frame increases upto the characteristic depth and decreases when the frame has been analysed for the full depth. It has been observed that shock spectrum analysis gives wide variation of responses in the frame compared to linear elastic analysis. Both increase and decrease in responses have been observed in the interior storeys. The good congruence shown by the two finite element models viz., discrete and continuum in linear static analysis has been absent in shock spectrum analysis. |
Description: | Department of Ship Technology, Cochin University of Science & Technology |
URI: | http://dyuthi.cusat.ac.in/purl/2876 |
Files | Size |
---|---|
Dyuthi-T0873.pdf | (8.920Mb) |
URI: | http://dyuthi.cusat.ac.in/purl/5622 |
Files | Size |
---|---|
Dyuthi T-2663.pdf | (19.44Mb) |
Abstract: | Tsunamis are water waves generated by a sudden vertical displacement of the water surface. They are waves generated in the ocean by the disturbance associated with seismic activity, under sea volcanic eruptions, submarine landslides, nuclear explosion or meteorite impacts with the ocean. These waves are generated in the ocean and travel into coastal bays, gulfs, estuaries and rivers. These waves travel as gravity waves with a velocity dependent on water depth. The term tsunami is Japanese and means harbour (tsu) and wave (nami). It has been named so because such waves often develop resonant phenomena in harbours after offshore earthquakes. |
Description: | Centre for Earth Science Studies, Thiruvananthapuram |
URI: | http://dyuthi.cusat.ac.in/purl/3739 |
Files | Size |
---|---|
Dyuthi-T1684.pdf | (7.700Mb) |
Abstract: | The motion instability is an important issue that occurs during the operation of towed underwater vehicles (TUV), which considerably affects the accuracy of high precision acoustic instrumentations housed inside the same. Out of the various parameters responsible for this, the disturbances from the tow-ship are the most significant one. The present study focus on the motion dynamics of an underwater towing system with ship induced disturbances as the input. The study focus on an innovative system called two-part towing. The methodology involves numerical modeling of the tow system, which consists of modeling of the tow-cables and vehicles formulation. Previous study in this direction used a segmental approach for the modeling of the cable. Even though, the model was successful in predicting the heave response of the tow-body, instabilities were observed in the numerical solution. The present study devises a simple approach called lumped mass spring model (LMSM) for the cable formulation. In this work, the traditional LMSM has been modified in two ways. First, by implementing advanced time integration procedures and secondly, use of a modified beam model which uses only translational degrees of freedoms for solving beam equation. A number of time integration procedures, such as Euler, Houbolt, Newmark and HHT-α were implemented in the traditional LMSM and the strength and weakness of each scheme were numerically estimated. In most of the previous studies, hydrodynamic forces acting on the tow-system such as drag and lift etc. are approximated as analytical expression of velocities. This approach restricts these models to use simple cylindrical shaped towed bodies and may not be applicable modern tow systems which are diversed in shape and complexity. Hence, this particular study, hydrodynamic parameters such as drag and lift of the tow-system are estimated using CFD techniques. To achieve this, a RANS based CFD code has been developed. Further, a new convection interpolation scheme for CFD simulation, called BNCUS, which is blend of cell based and node based formulation, was proposed in the study and numerically tested. To account for the fact that simulation takes considerable time in solving fluid dynamic equations, a dedicated parallel computing setup has been developed. Two types of computational parallelisms are explored in the current study, viz; the model for shared memory processors and distributed memory processors. In the present study, shared memory model was used for structural dynamic analysis of towing system, distributed memory one was devised in solving fluid dynamic equations. |
Description: | Department of Ship Technology Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/3751 |
Files | Size |
---|---|
Dyuthi-T1713.pdf | (4.757Mb) |
Abstract: | The present work aims at deciphering the processes that control the nutrient distribution along the EEZ (Exclusive Economic Zone of India) of the west coast of India and to bring out its linkage with primary and secondary productivity. This work assume utmost importance as very few studies have hitherto focused entirely on the EEZ of the west coast of India to address the biochemical responses brought about by monsoons. The present study examines the seasonal variations in physicochemical parameters and associated primary biological responses along the west coast of India. This study targets to measure and understand the shelf ocean exchange in a typical coastal upwelling region of the southeast Arabian Sea, and the influence of convective mixing along the northern part of the west coast of India. The study focuses more directly on coastal upwelling along the southwest coast of India, within the EEZ. The effects of coastal upwelling, eddy formation and the offshore advection are apparent in the present investigation. This has consequences to fisheries and climate, in energy transfer to the food chain and the increased sequestering of carbon in the ocean. The study also focuses on the Oxygen Minimum Zone (OMZ) and dentrification observed along the EEZ of the west coast of India on a seasonal scale. In the study, an attempt is also made to demarcate the geographical boundaries of the denitrification zone in the EEZ of India and on the nature and magnitude of these variations, on a seasonal and inter annual scales |
URI: | http://dyuthi.cusat.ac.in/purl/754 |
Files | Size |
---|---|
Dyuthi-T0215.pdf | (4.721Mb) |
Abstract: | This study was aimed at to characterize the spatio-temporal trends in the distributional characteristics of various species of nitrogen and phosphorus as well as to elucidate the factors and processes aflecting these nutrients in the dissolved, particulate and sedimentary phases of a river estuarine system. The main area of study is Chalakudy river in Kerala, which is a fresh water system originating from Anamalai hills and ending at Arabian Sea. Its basin is between I00 05 ’ to I00 35’ North latitude and 76” 15 ’ to 760 55’ East longitude. Being a riparian bufler zone, the dynamics of nutrient mobility tend to be more complex and variable in this river-estuarine system.The diflerent species of nitrogen estimated from the filtrate were nitrite-N, nitrateN, ammonia-N, urea-N, total nitrogen and residual nitrogen. The diflerent forms of phosphorus estimated from the filtrate were phosphate-P, total-P and residualP. Pre weighed sediments as well as particulate matter were analysed for quantijying nitrite-N, nitrate-N, ammonia-N and urea-N. Total nitrogen was estimated after digestion with potassium persulfate. Fractionation of phosphorus in sediment/particulate matter was performed by applying sequential extraction procedure. The dijferent forms of phosphorus thus estimated were loosely bound (exchangeable) P, Fe/Al bound P, polyphosphates, Ca bound P and refractory P. Sedimental total P was also measured directly by applying digestion method.The analyses carried out in this bimonthly annual survey have revealed specific information on the latent factors influencing the water quality pattern ofthe river. There was dependence among the chemical components of the river sediment and suspended matter, reflecting the water quality. A period of profound environmental change occurred and changes in various species had been noted in association with seasonal variations in the waterway, especially following enhanced river runoff during the monsoon. The results also successfully represented the distribution trend of nutrients during the rainy as well as dry season. Thus, the information gathered in this work will also be beneficial for those interested or involved in river management, conservation, regulation and policy making in regional and national levels. |
Description: | Dept.of Chemical Oceanography,Cochin University of Science and Technology. |
URI: | http://dyuthi.cusat.ac.in/purl/2991 |
Files | Size |
---|---|
Dyuthi-T0971.pdf | (20.24Mb) |
Abstract: | Most tropical aquatic environments are naturally fertile and their natural fertility is renewed very rapidly. Natural food for many cultivable organisms can be grown to the maximum by proper management. However, enrichment of the environment can be done through rational fertilization. Still further increase in stocking rates, can yield increased crop if adequate feeding is done. Thus fish and shellfish nutrition is an important aspect of the multidisciplinary subject of aquaculture. The oldest and most classical studies in physiology have investigated the nutritional needs of the species of interest to aquaculture. The alimentary requirements for proteins, lipids, mineral salts and vitamins have been established for some temperate species. But, the nutritional requirements of only few tropical species have been studied. Before formulating a diet, a thorough knowledge of the nutrient requirement of the species is essential. It is against this background that the present area of investigation has been identified. "Nutritional requirements of the fry of gold-spot mullet Liza parsia" is a comprehensive attempt to quantify the nutritional factors that are essential for producing healthy fingerlings for stocking the farms. Aspects such as the protein and lipid requirements of the fry, the vitamin essentiality, nutritive evaluation of protein and lipid sources suitable for compounding diets were covered in this research project. The ultimate aim has been to evolve practical diets which could be applied in the nursery phase for juvenile production. |
Description: | Central Marine Fisheries Research Institute |
URI: | http://dyuthi.cusat.ac.in/purl/3384 |
Files | Size |
---|---|
Dyuthi-T1361.pdf | (8.726Mb) |
Description: | Department of Marine Biology, Microbiology and Biochemistry, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/2176 |
Files | Size |
---|---|
Dyuthi-T0527.pdf | (2.543Mb) |
Abstract: | Man in his quest to explore food has turned towards the oceans and during the last five decades there has been phenomenal increase in the exploitation of the marine fisheries resources. The present study is carried out to determine the requirement of protein and water-soluble vitamins in the diet of juveniles of the Indian white prawn p.indicus using purified diets and to evaluate the nutritive value of a few plant and animal protein sources for the same species. A total of ten statistically designed experiments are conducted in the laboratory undermost identical conditions and following similar methodologies. The study also tries to suggest the essential and optimal requirements for protein as well as water-soluble vitamins in the diet of juvenile p.indicus |
Description: | Central Marine Fisheries Research Institute |
URI: | http://dyuthi.cusat.ac.in/purl/3167 |
Files | Size |
---|---|
Dyuthi-T1141.pdf | (13.62Mb) |
URI: | http://dyuthi.cusat.ac.in/purl/1194 |
Files | Size |
---|---|
Gopal C 1987.PDF | (332.9Kb) |
Dyuthi Digital Repository Copyright © 2007-2011 Cochin University of Science and Technology. Items in Dyuthi are protected by copyright, with all rights reserved, unless otherwise indicated.