Abstract: | This thesis investigates the potential use of zerocrossing information for speech sample estimation. It provides 21 new method tn) estimate speech samples using composite zerocrossings. A simple linear interpolation technique is developed for this purpose. By using this method the A/D converter can be avoided in a speech coder. The newly proposed zerocrossing sampling theory is supported with results of computer simulations using real speech data. The thesis also presents two methods for voiced/ unvoiced classification. One of these methods is based on a distance measure which is a function of short time zerocrossing rate and short time energy of the signal. The other one is based on the attractor dimension and entropy of the signal. Among these two methods the first one is simple and reguires only very few computations compared to the other. This method is used imtea later chapter to design an enhanced Adaptive Transform Coder. The later part of the thesis addresses a few problems in Adaptive Transform Coding and presents an improved ATC. Transform coefficient with maximum amplitude is considered as ‘side information’. This. enables more accurate tfiiz assignment enui step—size computation. A new bit reassignment scheme is also introduced in this work. Finally, sum ATC which applies switching between luiscrete Cosine Transform and Discrete Walsh-Hadamard Transform for voiced and unvoiced speech segments respectively is presented. Simulation results are provided to show the improved performance of the coder |
Description: | Department of Electronics, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/3396 |
Files | Size |
---|---|
Dyuthi-T1373.pdf | (4.336Mb) |
Abstract: | As emphasis towards sustainable and Renewable energy resources grows world-wide,interest in the capture and use of solar energy is increasing dramatically.Solar cells have been known and used for many years,but depletion of conventional energy resources resulted in the intensification of research on solar cells leading to new design and technique of fabrication.The current emphasis is directed towards high effiency inexpensive solar cells.This thesis includes deposition and characterization of CuInS2 and In2S3 thin films using chemical Spray Pyrolysis(CSP) technique.The optimum condition for these films to be used as absorber and buffer layer respectively in solar cells were thus found out.Solar cell with the stucture,ITO/CuInS2/In2S3/metal electrode was fabricated using these well-characterized films,which yielded an efficiency of 9.5%. |
Description: | Department of Physics, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/2375 |
Files | Size |
---|---|
Dyuthi-T0647.pdf | (13.64Mb) |
Abstract: | In this paper, we report the results of investigations on the potential of spray pyrolysis technique in depositing electron selective layer over larger area for the fabrication of inverted bulk-heterojunction polymer solar cells. The electron selective layer (In2S3) was deposited using spray pyrolysis technique and the linear heterojunction device thus fabricated exhibited good uniformity in photovoltaic properties throughout the area of the device. An MEH-PPV:PCBM inverted bulk-heterojunction device with In2S3 electron selective layer (active area of 3.25 3.25 cm2) was also fabricated and tested under indoor and outdoor conditions. Fromthe indoor measurements employing a tungsten halogen lamp (50mW/cm2 illumination), an opencircuit voltage of 0.41V and a short-circuit current of 5.6mA were obtained. On the other hand, the outdoor measurements under direct sunlight (74mW/cm2) yielded an open-circuit voltage of 0.46V and a short-circuit current of 9.37mA |
Description: | Phys. Status Solidi A 209, No. 1, 199–203 (2012) |
URI: | http://dyuthi.cusat.ac.in/purl/4721 |
Files | Size |
---|---|
Spray pyrolysed ... on polymer solar cells.pdf | (429.7Kb) |
Abstract: | In the early 19th century, industrial revolution was fuelled mainly by the development of machine based manufacturing and the increased use of coal. Later on, the focal point shifted to oil, thanks to the mass-production technology, ease of transport/storage and also the (less) environmental issues in comparison with the coal!! By the dawn of 21st century, due to the depletion of oil reserves and pollution resulting from heavy usage of oil the demand for clean energy was on the rising edge. This ever growing demand has propelled research on photovoltaics which has emerged successful and is currently being looked up to as the only solace for meeting our present day energy requirements. The proven PV technology on commercial scale is based on silicon but the recent boom in the demand for photovoltaic modules has in turn created a shortage in supply of silicon. Also the technology is still not accessible to common man. This has onset the research and development work on moderately efficient, eco-friendly and low cost photovoltaic devices (solar cells). Thin film photovoltaic modules have made a breakthrough entry in the PV market on these grounds. Thin films have the potential to revolutionize the present cost structure of solar cells by eliminating the use of the expensive silicon wafers that alone accounts for above 50% of total module manufacturing cost.Well developed thin film photovoltaic technologies are based on amorphous silicon, CdTe and CuInSe2. However the cell fabrication process using amorphous silicon requires handling of very toxic gases (like phosphene, silane and borane) and costly technologies for cell fabrication. In the case of other materials too, there are difficulties like maintaining stoichiometry (especially in large area films), alleged environmental hazards and high cost of indium. Hence there is an urgent need for the development of materials that are easy to prepare, eco-friendly and available in abundance. The work presented in this thesis is an attempt towards the development of a cost-effective, eco-friendly material for thin film solar cells using simple economically viable technique. Sn-based window and absorber layers deposited using Chemical Spray Pyrolysis (CSP) technique have been chosen for the purpose |
Description: | Department of Physics Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/3269 |
Files | Size |
---|---|
Dyuthi-T1243.pdf | (8.688Mb) |
Abstract: | In the early 19th century, industrial revolution was fuelled mainly by the development of machine based manufacturing and the increased use of coal. Later on, the focal point shifted to oil, thanks to the mass-production technology, ease of transport/storage and also the (less) environmental issues in comparison with the coal!! By the dawn of 21st century, due to the depletion of oil reserves and pollution resulting from heavy usage of oil the demand for clean energy was on the rising edge. This ever growing demand has propelled research on photovoltaics which has emerged successful and is currently being looked up to as the only solace for meeting our present day energy requirements. The proven PV technology on commercial scale is based on silicon but the recent boom in the demand for photovoltaic modules has in turn created a shortage in supply of silicon. Also the technology is still not accessible to common man. This has onset the research and development work on moderately efficient, eco-friendly and low cost photovoltaic devices (solar cells). Thin film photovoltaic modules have made a breakthrough entry in the PV market on these grounds. Thin films have the potential to revolutionize the present cost structure of solar cells by eliminating the use of the expensive silicon wafers that alone accounts for above 50% of total module manufacturing cost. |
URI: | http://dyuthi.cusat.ac.in/purl/5120 |
Files | Size |
---|---|
Dyuthi-T 2185.pdf | (9.607Mb) |
Abstract: | In recent years scientists have made rapid and significant advances in the field of semiconductor physics. One of the most important fields of current interest in materials science is the fundamental aspects and applications of conducting transparent oxide thin films (TCO). The characteristic properties of such coatings are low electrical resistivity and high transparency in the visible region. The first semitransparent and electrically conducting CdO film was reported as early as in 1907 [1]. Though early work on these films was performed out of purely scientific interest, substantial technological advances in such films were made after 1940. The technological interest in the study of transparent semiconducting films was generated mainly due to the potential applications of these materials both in industry and research. Such films demonstrated their utility as transparent electrical heaters for windscreens in the aircraft industry. However, during the last decade, these conducting transparent films have been widely used in a variety of other applications such as gas sensors [2], solar cells [3], heat reflectors [4], light emitting devices [5] and laser damage resistant coatings in high power laser technology [6]. Just a few materials dominate the current TCO industry and the two dominant markets for TCO’s are in architectural applications and flat panel displays. The architectural use of TCO is for energy efficient windows. Fluorine doped tin oxide (FTO), deposited using a pyrolysis process is the TCO usually finds maximum application. SnO2 also finds application ad coatings for windows, which are efficient in preventing radiative heat loss, due to low emissivity (0.16). Pyrolitic tin oxide is used in PV modules, touch screens and plasma displays. However indium tin oxide (ITO) is mostly used in the majority of flat panel display (FPD) applications. In FPDs, the basic function of ITO is as transparent electrodes. The volume of FPD’s produced, and hence the volume of ITO coatings produced, continues to grow rapidly. But the current increase in the cost of indium and the scarcity of this material created the difficulty in obtaining low cost TCOs. Hence search for alternative TCO materials has been a topic of active research for the last few decades. This resulted in the development of binary materials like ZnO, SnO2, CdO and ternary materials like II Zn2SnO4, CdSb2O6:Y, ZnSO3, GaInO3 etc. The use of multicomponent oxide materials makes it possible to have TCO films suitable for specialized applications because by altering their chemical compositions, one can control the electrical, optical, chemical and physical properties. But the advantages of using binary materials are the easiness to control the chemical compositions and depositions conditions. Recently, there were reports claiming the deposition of CdO:In films with a resistivity of the order of 10-5 ohm cm for flat panel displays and solar cells. However they find limited use because of Cd-Toxicity. In this regard, ZnO films developed in 1980s, are very useful as these use Zn, an abundant, inexpensive and nontoxic material. Resistivity of this material is still not very low, but can be reduced through doping with group-III elements like In, Al or Ga or with F [6]. Hence there is a great interest in ZnO as an alternative of ITO. In the present study, we prepared and characterized transparent and conducting ZnO thin films, using a cost effective technique viz Chemical Spray Pyrolysis (CSP). This technique is also suitable for large area film deposition. It involves spraying a solution, (usually aqueous) containing soluble salts of the constituents of the desired compound, onto a heated substrate. |
URI: | http://dyuthi.cusat.ac.in/purl/662 |
Files | Size |
---|---|
Dyuthi-T0457.pdf | (2.116Mb) |
URI: | http://dyuthi.cusat.ac.in/purl/4974 |
Files | Size |
---|---|
Dyuthi-T2045.pdf | (3.550Mb) |
Abstract: | The present work is an attempt to explain particle production in the early univese. We argue that nonzero values of the stress-energy tensor evaluated in squeezed vacuum state can be due to particle production and this supports the concept of particle production from zero-point quantum fluctuations. In the present calculation we use the squeezed coherent state introduced by Fan and Xiao [7]. The vacuum expectation values of stressenergy tensor defined prior to any dynamics in the background gravitational field give all information about particle production. Squeezing of the vacuum is achieved by means of the background gravitational field, which plays the role of a parametric amplifier [8]. The present calculation shows that the vacuum expectation value of the energy density and pressure contain terms in addition to the classical zero-point energy terms. The calculation of the particle production probability shows that the probability increases as the squeezing parameter increases, reaches a maximum value, and then decreases. |
Description: | International Journal of Theoretical Physics, Vol. 39, No. 2, 2000 |
URI: | http://dyuthi.cusat.ac.in/purl/4173 |
Files | Size |
---|---|
Squeezed Cohere ... n in the EarlyUniverse.pdf | (75.28Kb) |
Abstract: | The present work is an attempt to explain particle production in the early univese. We argue that nonzero values of the stress-energy tensor evaluated in squeezed vacuum state can be due to particle production and this supports the concept of particle production from zero-point quantum fluctuations. In the present calculation we use the squeezed coherent state introduced by Fan and Xiao [7]. The vacuum expectation values of stressenergy tensor defined prior to any dynamics in the background gravitational field give all information about particle production. Squeezing of the vacuum is achieved by means of the background gravitational field, which plays the role of a parametric amplifier [8]. The present calculation shows that the vacuum expectation value of the energy density and pressure contain terms in addition to the classical zero-point energy terms. The calculation of the particle production probability shows that the probability increases as the squeezing parameter increases, reaches a maximum value, and then decreases. |
Description: | International Journal of Theoretical Physics, Vol. 39, No. 2, 2000 |
URI: | http://dyuthi.cusat.ac.in/purl/4148 |
Files | Size |
---|---|
Squeezed Cohere ... in the Early Universe.pdf | (75.28Kb) |
Abstract: | The use of a split-ring resonator (SRR)-loaded waveguide for the design of a band-rejection filter with adjustable bandwidth is reported. The width of the stopband can be adjusted by suitably positioning the SRR array in the waveguide. The rejection band can be made very narrow by placing the array at the electric-field minimum. The stopband attenuation depends on the number of unit cells in the array. |
URI: | http://dyuthi.cusat.ac.in/purl/2737 |
Files | Size |
---|---|
Dyuthi-P00371.pdf | (206.8Kb) |
Abstract: | HINDI |
Description: | Department of Hindi, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/4849 |
Files | Size |
---|---|
Dyuthi-T1946.pdf | (4.662Mb) |
Abstract: | According to current knowledge, convection over the tropical oceans increases with sea surface temperature (SST) from 26 to 29 °C, and at SSTs above 29 °C, it sharply decreases. Our research shows that it is only over the summer warm pool areas of Indian and west Pacific Oceans (monsoon areas) where the zone of maximum SST is away from the equator that this kind of SST-convection relationship exists. In these areas (1) convection is related to the SST gradient that generates low-level moisture convergence and upward vertical motion in the atmosphere. This has modelling support. Regions of SST maxima have low SST gradients and therefore feeble convection. (2) Convection initiated by SST gradient produces strong wind fields particularly cross-equatorial low-level jetstreams (LLJs) on the equator-ward side of the warm pool and both the convection and LLJ grow through a positive feedback process. Thus, large values of convection are associated with the cyclonic vorticity of the LLJ in the atmospheric boundary layer. In the inter-tropical convergence zone (ITCZ) over the east Pacific Ocean and the south Pacific convergence zone (SPCZ) over the west Pacific Ocean, low-level winds from north and south hemisphere converge in the zone of maximum SST, which lies close to the equator producing there elongated bands of deep convection, where we find that convection increases with SST for the full range of SSTs unlike in the warm pool regions. The low-level wind divergence computed using QuikSCAT winds has large and significant linear correlation with convection in both the warm pool and ITCZ/SPCZ areas. But the linear correlation between SST and convection is large only for the ITCZ/SPCZ. These findings have important implications for the modelling of largescale atmospheric circulations and the associated convective rainfall over the tropical oceans |
Description: | Int. J. Climatol. (2012) |
URI: | http://dyuthi.cusat.ac.in/purl/3796 |
Files | Size |
---|---|
sst-conv-relation-IJC.pdf | (982.6Kb) |
Abstract: | We consider the stability properties of spatial and temporal periodic orbits of one-dimensional coupled-map lattices. The stability matrices for them are of the block-circulant form. This helps us to reduce the problem of stability of spatially periodic orbits to the smaller orbits corresponding to the building blocks of spatial periodicity, enabling us to obtain the conditions for stability in terms of those for smaller orbits. |
URI: | http://dyuthi.cusat.ac.in/purl/2537 |
Files | Size |
---|---|
Dyuthi-P0112.pdf | (184.9Kb) |
Abstract: | This study is about the stability of random sums and extremes.The difficulty in finding exact sampling distributions resulted in considerable problems of computing probabilities concerning the sums that involve a large number of terms.Functions of sample observations that are natural interest other than the sum,are the extremes,that is , the minimum and the maximum of the observations.Extreme value distributions also arise in problems like the study of size effect on material strengths,the reliability of parallel and series systems made up of large number of components,record values and assessing the levels of air pollution.It may be noticed that the theories of sums and extremes are mutually connected.For instance,in the search for asymptotic normality of sums ,it is assumed that at least the variance of the population is finite.In such cases the contributions of the extremes to the sum of independent and identically distributed(i.i.d) r.vs is negligible. |
URI: | http://dyuthi.cusat.ac.in/purl/776 |
Files | Size |
---|---|
Dyuthi-T0089.pdf | (3.775Mb) |
URI: | http://dyuthi.cusat.ac.in/purl/5232 |
Files | Size |
---|---|
Dyuthi T-2267.pdf | (9.710Mb) |
Abstract: | The study entitled standardization of optimum conditions for the production of glucosamine hydrochloride from chitin. Shellfish processing industries around the world turn out a significant quantity of head and shell as industrial waste. The waste must be removed immediately to prevent the contamination to the processing environment. The technique that are available for their disposal include ocean dumping, incineration or disposal of landfill sites. In this thesis the techniques and methods are used to process glucosamine hydrochloride from crustacean processing waste. Chitin is a nitrogenous polysaccharide, which is white, hard, inelastic, found in outer skeleton of insects, crabs, shrimp and lobsters and in the internal structures of other invertebrates. Glucosamine can be considered as a nutraceutical product by virtue of its properties. It is important for healthy skin, and plays a major role in the healing of surgical incisions and skin wounds. Deproteinisation of shrimp shell had significant effect on quality of chitin. Demineralization is also influences chitin quality. Solvents used for glucosamine hydrochloride affects the final yield and purity. |
URI: | http://dyuthi.cusat.ac.in/purl/85 |
Files | Size |
---|---|
Dyuthi-T0086.pdf | (4.856Mb) |
Abstract: | In the present work, Indigenous polymer coated Tin Free Steel cans were analyzed fortheir suitability for thermal processing and storage of fish and fish products following standard methods. The raw materials used for the development of ready to eat thermally processed fish products were found to be of fresh condition. The values for various biochemical and microbiological parameters of the raw materials were well within the limits. Based on the analysis of commercial sterility, instrumental colour, texture, WB-shear force and sensory parameters, squid masala processed to F0 value of 8 min with a total process time of 38.5 min and cook value of 92 min was chosen as the optimum for squid masala in tin free steel cans while shrimp curry processed to F0 7 min with total process time of 44.0 min and cook value of 91.1 min was found to be ideal and was selected for storage study. Squid masala and shrimp curry thermally processed in indigenous polymer coated TFS cans were found to be acceptable even after one year of storage at room temperaturebased on the analysis of various sensory and biochemical parameters. Analysis of the Commission Internationale d’ Eclirage L*, a* and b* color values showed that the duration of exposure to heat treatment influenced the color parameters: the lightness (L*) and yellowness (b*)decreased, and the redness (a*) significantly increased with the increase in processing time or reduction in processing temperature.Instrumental analysis of texture showed that hardness-1 & 2 decreased with reduction in retort temperature while cohesiveness value did not show any appreciable change with decrease in temperature of processing. Other texture profile parameters like gumminess, springiness and chewiness decreased significantly with increase of processing time. W-B shear force values of mackerel meat processed at 130 °C were significantly higher than those processed at 121.1 and 115 °C. HTST processing of mackerel in brine helped in reducing the process time and improving the quality.The study also indicated that indigenous polymer coated TFS cans with easy openends can be a viable alternative to the conventional tin and aluminium cans. The industry can utilize these cans for processing ready to eat fish and shell fish products for both domestic and export markets. This will help in reviving the canning industry in India. |
Description: | Faculty of Marine Sciences, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/xmlui/purl/1936 |
Files | Size |
---|---|
Dyuthi-T0458.pdf | (2.105Mb) |
Abstract: | This study is an attempt to situate the quality of life and standard of living of local communities in ecotourism destinations inter alia their perception on forest conservation and the satisfaction level of the local community. 650 EDC/VSS members from Kerala demarcated into three zones constitute the data source. Four variables have been considered for evaluating the quality of life of the stakeholders of ecotourism sites, which is then funneled to the income-education spectrum for hypothesizing into the SLI framework. Zone-wise analysis of the community members working in tourism sector shows that the community members have benefited totally from tourism development in the region as they have got both employments as well as secured livelihood options. Most of the quality of life-indicators of the community in the eco-tourist centres show a promising position. The community perception does not show any negative impact on environment as well as on their local culture. |
Description: | Journal of Economics and Sustainable Development,Vol.3, No.2, 2012 |
URI: | http://dyuthi.cusat.ac.in/purl/4594 |
Files | Size |
---|---|
Standard of Liv ... An InterZone Analysis.pdf | (448.5Kb) |
Abstract: | Filled compounds of natural rubber, isobutylene-isoprene rubber and styrene-butadiene rubber compounds were extruded through a laboratory extruder by varying the feeding rate at different temperatures and revolutions per minute. The extruded compounds were vulcanized up to their optimum cure times and the mechanical properties of the vulcanizates were determined. The properties suggest that there is a particular feeding rate in the starved fed region which results in maximum mechanical properties. The study shows that running the extruder at a slightly starved condition is an attractive means of improving the physical properties. |
URI: | http://dyuthi.cusat.ac.in/purl/831 |
Files | Size |
---|---|
P J Joseph Fran ... rved extrusion...,1997.PDF | (7.505Mb) |
Dyuthi Digital Repository Copyright © 2007-2011 Cochin University of Science and Technology. Items in Dyuthi are protected by copyright, with all rights reserved, unless otherwise indicated.