| Abstract: | This study investigated the enhancement of solar disinfection using custom-made batch reactors with reflective (foil-backed) or absorptive (black-backed) rear surfaces, under a range of weather conditions in India. Plate counts of Escherichia coli ATCC11775 were made under aerobic conditions and under conditions where reactive oxygen species (ROS) were neutralised, i.e. in growth medium supplemented with 0.05% w/v sodium pyruvate plus incubation under anaerobic conditions. While the addition of either an absorptive or a reflective backing enhanced reactor performance under strong sunlight, the reflective reactor was the only system to show consistent enhancement under low sunlight, where the process was slowest. Counts performed under ROS-neutralised conditions were slightly higher than those in air, indicating that a fraction of the cells become sub-lethally injured during exposure to sunlight to the extent that they were unable to grow aerobically. However, the influence of this phenomenon on the dynamics of inactivation was relatively small |
| Description: | WATER RESEARCH 40 (2006) 721 – 727 |
| URI: | http://dyuthi.cusat.ac.in/purl/4032 |
| Files | Size |
|---|---|
| Comparative eff ... smissive rear surfaces.pdf | (297.7Kb) |
| Abstract: | There is a growing commercial interest in the ¢sh, Puntius ¢lamentosus, in the ornamental ¢sh trade in India and elsewhere.The trade is, however, hampered by severe mortalities during transport of the ¢sh owing to insu⁄cient data available on the use of anaesthetics. To resolve this problem, we evaluated the e⁄cacy of two anaesthetics, MS-222 and benzocaine, in sedating P. ¢lamentosus in simulated transportation experiments and used stress response parameters such as cortisol and blood glucose levels to perform assessments. We observed that MS-222 at 40 mg L 1 and benzocaine at 20mg L 1 were su⁄- cient to induce sedation for 48 h. Above these concentrations, both the anaesthetics adversely a¡ected the ¢sh and resulted inmortalities. Both anaesthetics signi¢cantly lowered the blood cortisol and glucose levels compared with the unsedated controls. Importantly, the anaesthetics treatment signi¢cantly lowered the post-transport mortality in the ¢sh. The results of the study show that MS-222 and benzocaine could be used as sedatives to alleviate transport- related stress in P. ¢lamentosus to improve their post-transport survival and hence reduce economic loss. |
| Description: | Aquaculture Research, 2010, 41, 309-314 |
| URI: | http://dyuthi.cusat.ac.in/purl/4115 |
| Files | Size |
|---|---|
| Comparative eff ... mentosus(Valenciennes).pdf | (290.5Kb) |
| Abstract: | The design and fabrication of fiber based ammonia sensors employing Bromothymol blue and Chitosan as sensing elements are presented in this paper. In the presence of ammonia gas the absorption of Bromothymol blue changes while in the case of Chitosan the refractive index changes which in turn modulates the intensity of light propagating through a fiber. |
| URI: | http://dyuthi.cusat.ac.in/xmlui/purl/2042 |
| Files | Size |
|---|---|
| Comparative performance of two...pdf | (162.7Kb) |
| Abstract: | Severe local storms, including tornadoes, damaging hail and wind gusts, frequently occur over the eastern and northeastern states of India during the pre-monsoon season (March-May). Forecasting thunderstorms is one of the most difficult tasks in weather prediction, due to their rather small spatial and temporal extension and the inherent non-linearity of their dynamics and physics. In this paper, sensitivity experiments are conducted with the WRF-NMM model to test the impact of convective parameterization schemes on simulating severe thunderstorms that occurred over Kolkata on 20 May 2006 and 21 May 2007 and validated the model results with observation. In addition, a simulation without convective parameterization scheme was performed for each case to determine if the model could simulate the convection explicitly. A statistical analysis based on mean absolute error, root mean square error and correlation coefficient is performed for comparisons between the simulated and observed data with different convective schemes. This study shows that the prediction of thunderstorm affected parameters is sensitive to convective schemes. The Grell-Devenyi cloud ensemble convective scheme is well simulated the thunderstorm activities in terms of time, intensity and the region of occurrence of the events as compared to other convective schemes and also explicit scheme |
| Description: | International Journal of Computer Applications (0975 – 8887) Volume 33– No.6, November 2011 |
| URI: | http://dyuthi.cusat.ac.in/purl/4092 |
| Files | Size |
|---|---|
| A Comparative S ... hemes in WRF-NMM Model.pdf | (564.8Kb) |
| Abstract: | This study was conducted to identify the concentration dependence of the operating wavelengths and the relative intensities in which a dye mixture doped polymer optical fibre can operate. A comparative study of the radiative and Forster type energy transfer processes in Coumarin 540:Rhodamine 6G, Coumarin 540:Rhodamine B and Rhodamine 6G:Rhodamine B in methyl methacrylate (MMA) and poly(methyl methacrylate) (PMMA) was done by fabricating a series of dye mixture doped polymer rods which have two emission peaks with varying relative intensities. These rods can be used as preforms for the fabrication of polymer optical fibre amplifiers operating in the multi-wavelength regime. The 445 nm line from an Nd:YAG pumped optical parametric oscillator (OPO) was used as the excitation source for the first two dye pairs and a frequency doubled Nd:YAG laser emitting at 532 nm was used to excite the Rh 6G:Rh B pair. The fluorescence lifetimes of the donor molecule in pure form as well as in the mixtures were experimentally measured in both monomer and polymer matrices by time-correlated single photon counting technique. The energy transfer rate constants and transfer efficiencies were calculated and their dependence on the acceptor concentration was analysed. It was found that radiative energy transfer mechanisms are more efficient in all the three dye pairs in liquid and solid matrices. |
| URI: | http://dyuthi.cusat.ac.in/purl/2421 |
| Files | Size |
|---|---|
| Dyuthi-P0269.pdf | (903.9Kb) |
| Abstract: | A comparative study of two biopolymer based fiber optic humidity sensors is presented in this paper. Sensing elements Agarose and Chitosan swells in the presence of water vapour and undergoes changes in refractive index and modulates the intensity of light propagating through a fiber with Agarose or Chitosan as cladding. |
| URI: | http://dyuthi.cusat.ac.in/purl/2590 |
| Files | Size |
|---|---|
| Dyuthi-P0150.pdf | (563.6Kb) |
| Abstract: | A primary medium for the human beings to communicate through language is Speech. Automatic Speech Recognition is wide spread today. Recognizing single digits is vital to a number of applications such as voice dialling of telephone numbers, automatic data entry, credit card entry, PIN (personal identification number) entry, entry of access codes for transactions, etc. In this paper we present a comparative study of SVM (Support Vector Machine) and HMM (Hidden Markov Model) to recognize and identify the digits used in Malayalam speech. |
| URI: | http://dyuthi.cusat.ac.in/purl/4232 |
| Files | Size |
|---|---|
| A Comparative s ... alam Digit Recognition.pdf | (200.2Kb) |
| Abstract: | Welding of high strength and low weight materials like Aluminium Alloys without any defects by conventional welding techniques is a major challenge in industries. Hence research on solid state welding techniques like Friction stir welding and Friction welding techniques have got much importance in joining of Aluminium alloys. However most of the industries are not changing conventional techniques as skilled workers are available on that area. Most common conventional welding techniques used for joining of Aluminium alloys are Gas welding and Arc welding. Friction welding is a solid-state welding process that generates heat through mechanical friction between a moving and a stationary component with the addition of a lateral force called “upset” to plast ically displace and fuse the materials. In this work, experimental study on tensile and micro structural characteristics of welded joints formed from conventional welding techniques and Rotary friction welding(suitable for weld specimens with circular cross section) has been carried out and the same were compared. The process parameters for arc welding used was 50-70 Amp reverse polarity DC and electrodes of 2.3mm diameter. In Gas welding, the parameters were oxy acetylene neural flame at 3200°C and 3mm electrodes . In the case of friction welding an axial pressure loading of 3Mpa with 5 MPa as upsetting pressure and 500 rpm were used to obtain good welded joints. Tensile characteristic studies of Arc welded joints and Gas welded joints showed 48% and 60 % variations respectively from the maximum load bearing characteristics of parent metal. In the case of friction welded joint, the variation was found to 46%. Micro structural evaluation of conventionally welded joints exhibited clear distinct zones of various weld regions. In the case of friction welded joint micro structural photographs showed comparable features both in parent metal and welded region. Thus the tensile characteristic study and microstructure evaluations proved that friction welded joints are good in both aspects compared to conventionally welded joints. |
| Description: | International Journal of Innovative Research in Science, Engineering and Technology,Volume 2, Special Issue 1, December 2013 |
| URI: | http://dyuthi.cusat.ac.in/purl/4677 |
| Files | Size |
|---|---|
| A Comparative S ... f Aluminium Alloy 6061.pdf | (704.1Kb) |
| Abstract: | Speech is a natural mode of communication for people and speech recognition is an intensive area of research due to its versatile applications. This paper presents a comparative study of various feature extraction methods based on wavelets for recognizing isolated spoken words. Isolated words from Malayalam, one of the four major Dravidian languages of southern India are chosen for recognition. This work includes two speech recognition methods. First one is a hybrid approach with Discrete Wavelet Transforms and Artificial Neural Networks and the second method uses a combination of Wavelet Packet Decomposition and Artificial Neural Networks. Features are extracted by using Discrete Wavelet Transforms (DWT) and Wavelet Packet Decomposition (WPD). Training, testing and pattern recognition are performed using Artificial Neural Networks (ANN). The proposed method is implemented for 50 speakers uttering 20 isolated words each. The experimental results obtained show the efficiency of these techniques in recognizing speech |
| URI: | http://dyuthi.cusat.ac.in/purl/3912 |
| Files | Size |
|---|---|
| A Comparative S ... Isolated Spoken Words.pdf | (342.6Kb) |
| Abstract: | The catalyst compositions of the Zn1−xCOxFe2O4 (x= 0, 0.2, 0.5, 0.8 and 1.0) spiel series possessing ‘x’ values, x less than or equal to 0.5, are unique for selective N-monomethylation of aniline using methanol as the alkylating agent. Since dimethyl carbonate (DMC) is another potential non-toxic alkylating agent, alkylation of aniline was investigated over various Zn–Co ferrites using DMC as the alkylating agent. The merits and demerits of the two alkylating agents are compared. Catalytic activity followed a similar trend with respect to the composition of the ferrospinel systems. DMC is active at comparatively low temperature, where methanol shows only mild activity. However, on the selectivity basis, DMC as an alkylating agent could not compete with methanol, since the former gave appreciable amounts of N,N-dimethylaniline (NNDMA) even at low temperature where methanol gave nearly 99% N-methylaniline (NMA) selectivity. As in the case of methanol, DMC also did not give any C-alkylated products. |
| URI: | http://dyuthi.cusat.ac.in/purl/2244 |
| Files | Size |
|---|---|
| Dyuthi-SS42.pdf | (158.0Kb) |
| Abstract: | A comparative study on the anisole methylation with methanol over lanthanum-promoted Sn02 catalyst and its sulfate-doped analogue is presented. A maximum 2.6-xylenol selectivity of 82% was achieved at 400 degreeC under optimized conditions at an anisole conversion of 65% over lanthanum-promoted Sn02 catalyst. The sulfate modification resulted in the dealkylation of anisole to phenol followed by several unselective side reactions due to the creation of strong acid sites. The activity of lanthanum-modified tin oxide catalysts in the selective formation of 2.6-xylenol is ascribed to the presence of weak Lewis acid sites and comparatively stronger basic sites. |
| URI: | http://dyuthi.cusat.ac.in/purl/2170 |
| Files | Size |
|---|---|
| Dyuthi-SS10.pdf | (241.3Kb) |
| Abstract: | In this paper, microstrip lines magnetically coupled to splitring resonators (SRRs) are conquved to electromagnetic bundgup (EBG) nr,rrostrip lines in terns q/ their stop-heard penjbrnmrnce and dimensions. In bath types o/ trunsmis•siou lines, signal propagation is inhibited in it certain jequency bwuL For EBG microstrip lines, the central frequency of such a forbidden band is determined by the period of the structure, whereas in SRR-hased microstrip lines the position of the frequency gap depends on the quasi-static resonant frequency of the rings. The main relevant conrributiun of this paper is to provide a tuning procedure to control the gap width in SRR microstrip lines, and to show that by using SRRs, device dimensions ale much smaller than those required by EBGs in order to obtain similar stop-banal performance. This has been demonstrated by fill-wave electromagnetic simulations and experimentally verified from the characterization ql two fabricated microstrip lines: one with rectangular SRRs etched on the upper substrate side, and the other with a periodic perturbation cf'strip width. For similar rejection and 1-(;H,. gap width centered at 4.5 Gllz, it has been found that the SRR microstrip line is•,fve times shorter. In addition, no ripple is appreciable in the allowed band for the .SRR-hared structure, whereas due to dispersion, certain mismatch is expected in the EBG prototype. Due to the high-frequency selectivity, controllable gap width, and small dimensions, it is believed that SRR coupled to planar transmission lines can have an actual impact on the design of stop-band filters compatible with planar technology, and can be an alternative to present solutions based on distributed approaches or EBG |
| URI: | http://dyuthi.cusat.ac.in/purl/1421 |
| Files | Size |
|---|---|
| Comparison of e ... s stop band structures.PDF | (686.9Kb) |
| Abstract: | Microwave properties of conductive polymers is crucial because of their wide areas of applications such as coating in reflector antennas, coating in electronic equipments, firequenry selective .surfaces, EMI materials, satellite communication links, microchip antennas, and medical applications. This work involves a comparative study of dielectric properties of selected conducting polymers such as polyaniline. poly(3,4-eth),lenedio.syt2iophene), polvthiophene, polvpvrrole. and pohparaphenylene diazomethine (PPDA) in microwave and DC,fields. The inicrowave properties such as dielectric constant, dielectric loss. absorption coefficient, heating coefficient, skin depth, and conductivity in the microwave frequency (S hand), and DC fields were compared. PEDOT and polccuiiline were found to exhibit excellent properties in DC field and microwave frequencies, which make thein potential materials in many of the alorenientioned applications |
| URI: | http://dyuthi.cusat.ac.in/purl/804 |
| Files | Size |
|---|---|
| K.Lakshmi and o ... microwave....June2007.PDF | (4.073Mb) |
| Abstract: | This paper compares statistical technique of paraphrase identification to semantic technique of paraphrase identification. The statistical techniques used for comparison are word set and word-order based methods where as the semantic technique used is the WordNet similarity matrix method described by Stevenson and Fernando in [3]. |
| Description: | 2012 International Conference on Data Science & Engineering (ICDSE) |
| URI: | http://dyuthi.cusat.ac.in/purl/4109 |
| Files | Size |
|---|---|
| Comparison of S ... aphrase Identification.pdf | (88.92Kb) |
| Abstract: | In this paper, a comparison study among three neuralnetwork algorithms for the synthesis of array patterns is presented. The neural networks are used to estimate the array elements' excitations for an arbitrary pattern. The architecture of the neural networks is discussed and simulation results are presented. Two new neural networks, based on radial basis functions (RBFs) and wavelet neural networks (WNNs), are introduced. The proposed networks offer a more efficient synthesis procedure, as compared to other available techniques |
| URI: | http://dyuthi.cusat.ac.in/purl/1413 |
| Files | Size |
|---|---|
| Comparison stud ... using neural networks.PDF | (379.2Kb) |
| Abstract: | The principal objective of this study was to explore the compatibility of a blend of two synthetic elastomers viz., ethylene-propylene-diene rubber (EPDM) and chlorobutyl rubber (CIIR). Various commercial grades of EPDM were blended with a specific grade of CIIR at different proportions. The mechanical properties such as tensile strength, tear strength, ageing resistance, etc. were studied. On the basis of the observed physical properties, two particular grades of EPDM were found to be compatible with CIIR. Differential scanning calorimetry and scanning electron microscopy confirmed the results. Chlorosulphonated polyethylene was added as a compatibilizing agent to overcome the phase separation of the other two incompatible grades of EPDM in blending with CIIR. The results revealed that the addition of compatibilizer greatly improves the compatibility and thereby the properties of the blends. |
| URI: | http://dyuthi.cusat.ac.in/xmlui/purl/2001 |
| Files | Size |
|---|---|
| Compatibility studies on....pdf | (403.3Kb) |
| Abstract: | Bank switching in embedded processors having partitioned memory architecture results in code size as well as run time overhead. An algorithm and its application to assist the compiler in eliminating the redundant bank switching codes introduced and deciding the optimum data allocation to banked memory is presented in this work. A relation matrix formed for the memory bank state transition corresponding to each bank selection instruction is used for the detection of redundant codes. Data allocation to memory is done by considering all possible permutation of memory banks and combination of data. The compiler output corresponding to each data mapping scheme is subjected to a static machine code analysis which identifies the one with minimum number of bank switching codes. Even though the method is compiler independent, the algorithm utilizes certain architectural features of the target processor. A prototype based on PIC 16F87X microcontrollers is described. This method scales well into larger number of memory blocks and other architectures so that high performance compilers can integrate this technique for efficient code generation. The technique is illustrated with an example |
| Description: | International Journal of Software Engineering and Its Applications Vol. 6, No. 1, January, 2012 |
| URI: | http://dyuthi.cusat.ac.in/purl/4668 |
| Files | Size |
|---|---|
| A Compiler Inte ... ry Embedded Processors.pdf | (577.3Kb) |
| Abstract: | This paper reports the synthesis of a series of six new polystyrene anchored metal complexes of Co(II), Fe(III), Ni(II), Cu(II), Zn(II), and dioxouanium(VI) using the polystyrene anchored Schiff base of 2-nitrobenzaldehyde and the corresponding metal salts. The metal salts used were anhydrous FeCl3, CoCl2 Æ 6H2O, Ni(CH3COO)2 Æ 4H2O, Cu(CH3- COO)2 Æ H2O, Zn(CH3COO)2 Æ 2H2O, and UO2(CH3COO) Æ 2H2O. Physico chemical characterizations have been made from diffuse reflectance and vibrational spectra, elemental analysis, magnetic measurements, and TG studies. The elemental analysis suggest a 1:2 metal:ligand ratio when the complexation has carried out at 70 C for about 12 h reflux. The ligand is monodentate and coordinates through the azomethine nitrogen. The Fe(III), Co(II), Ni(II), and Cu(II) complexes are all paramagnetic whereas Zn(II) and U(VI) are diamagnetic. Zn(II) is assigned a tetrahedral structure, Cu(II) and Co(II) are assigned a square planar structure and Fe(III), Ni(II), and U(VI) are all assigned an octahedral structure. The polystyrene anchored ligand has been developed as an excellent reagent for the removal of Cu(II). Optimum conditions have been developed for the removal of metal ion from solutions by studying the effect of change of concentration of metal ion, ligand, effect of pH, time of reflux, and interference effect of other ions. It was found that within a span of 20 min it is possible to remove 90% of the metal ion from a 30 ppm metal ion solution in the pH range 4–5.5. |
| URI: | http://dyuthi.cusat.ac.in/purl/518 |
| Files | Size |
|---|---|
| REACT2135.pdf | (271.9Kb) |
| Abstract: | n this paper, a time series complexity analysis of dense array electroencephalogram signals is carried out using the recently introduced Sample Entropy (SampEn) measure. This statistic quantifies the regularity in signals recorded from systems that can vary from the purely deterministic to purely stochastic realm. The present analysis is conducted with an objective of gaining insight into complexity variations related to changing brain dynamics for EEG recorded from the three cases of passive, eyes closed condition, a mental arithmetic task and the same mental task carried out after a physical exertion task. It is observed that the statistic is a robust quantifier of complexity suited for short physiological signals such as the EEG and it points to the specific brain regions that exhibit lowered complexity during the mental task state as compared to a passive, relaxed state. In the case of mental tasks carried out before and after the performance of a physical exercise, the statistic can detect the variations brought in by the intermediate fatigue inducing exercise period. This enhances its utility in detecting subtle changes in the brain state that can find wider scope for applications in EEG based brain studies. |
| URI: | http://dyuthi.cusat.ac.in/purl/2602 |
| Files | Size |
|---|---|
| Dyuthi-P0162.pdf | (1.121Mb) |
Dyuthi Digital Repository Copyright © 2007-2011 Cochin University of Science and Technology. Items in Dyuthi are protected by copyright, with all rights reserved, unless otherwise indicated.