Abstract: | The reaction of aniline with methanol was carried out over Zn1-xNixFe2O4 (x= 0, 0.2, 0.5, 0.8 and 1) type systems in a fixed-bed down-flow reactor. It was observed that systems possessing low ``x'' values are highly selective and active for mono N-alkylation of aniline leading to N-methyl aniline. Selectivity for N-methyl aniline over ZnFe2O4 was more than 99% under the optimized reaction conditions. Even at methanol to aniline molar ratio of 2, the yield of N-methyl aniline was nearly 55.5%, whereas its yield exceeded 67% at the molar ratio of 7. The Lewis acid sites of the catalysts are mainly responsible for the good catalytic performance. Cation distribution in the spinel lattice influences their acido-basic properties, and hence, these factors have been considered as helpful to evaluate the activity and stability of the systems. |
URI: | http://dyuthi.cusat.ac.in/purl/2245 |
Files | Size |
---|---|
Dyuthi-SS43.pdf | (608.8Kb) |
Abstract: | A series of ferrites having the general formula Zn1-xCoxFe2O4 (x=0, 0.2, 0.5, 0.8 and 1.0)were prepared by soft chemical route. The materials were characterized by adopting various physico-chemical methods. The reaction of aniline with methanol was studied in a fixed-bed reactor system as a potential source for the production of various methyl anilines. It was observed that systems possessing low ‘ x’ values are highly selective and active for N-monoalkylation of aniline leading to N-methylaniline. Reaction parameters were properly varied to optimize the reaction conditions for obtaining N-methylaniline selectively and in better yield. Among the systems Zn0.8Co0.2Fe2O4 is remarkable due to its very high activity and excellent stability. Under the optimized conditions N-methylaniline selectivity exceeded 98%. Even at a methanol to aniline molar ratio of 2, the yield of N-methylaniline was nearly 50%, whereas its yield exceeded 71% at the molar ratio of 5. ZnFe2O4, though executed better conversion than Zn0.8Co0.2Fe2O4 in the initial period of the run, deactivates quickly as the reaction proceeds. The Lewis acidity of the catalysts is mainly responsible for the good performance. Cation distribution in the spinel lattice influences their acido-basic properties and, hence, these factors have been considered as helpful parameters to evaluate the activity of the systems. |
URI: | http://dyuthi.cusat.ac.in/purl/2249 |
Files | Size |
---|---|
Dyuthi-SS44.pdf | (385.6Kb) |
Abstract: | The self adhesion behaviour of thermoplastic polyurethane (TPU) in itself and its composite with short Kevlar fibre with respect to contact time, temperature, pressure, and fibre loading has been studied. The adhesion strength showed two linear increments of different slopes with respect to the square root of time: with temperature and pressure of contact, the adhesion strength was improved. The maximum strength was obtained with 20 phr of short fibre in only one of the mating substrates in the peel test sample. The duration for wetting and diffusion was shifted to longer time intervals with fibres loaded in both the substrates. |
URI: | http://dyuthi.cusat.ac.in/purl/883 |
Files | Size |
---|---|
Golok , B, S K ... short kevlar...........PDF | (5.744Mb) |
Abstract: | This work presents an efficient method for volume rendering of glioma tumors from segmented 2D MRI Datasets with user interactive control, by replacing manual segmentation required in the state of art methods. The most common primary brain tumors are gliomas, evolving from the cerebral supportive cells. For clinical follow-up, the evaluation of the pre- operative tumor volume is essential. Tumor portions were automatically segmented from 2D MR images using morphological filtering techniques. These seg- mented tumor slices were propagated and modeled with the software package. The 3D modeled tumor consists of gray level values of the original image with exact tumor boundary. Axial slices of FLAIR and T2 weighted images were used for extracting tumors. Volumetric assessment of tumor volume with manual segmentation of its outlines is a time-consuming proc- ess and is prone to error. These defects are overcome in this method. Authors verified the performance of our method on several sets of MRI scans. The 3D modeling was also done using segmented 2D slices with the help of a medical software package called 3D DOCTOR for verification purposes. The results were validated with the ground truth models by the Radi- ologist. |
Description: | J. Biomedical Science and Engineering, 2012, 5, 378-383 |
URI: | http://dyuthi.cusat.ac.in/purl/4569 |
Files | Size |
---|---|
A semi-automati ... tumors from brain MRI.pdf | (462.7Kb) |
Abstract: | The fabrication and characterization of a fibre optic pH sensor based on evanescent wave absorption is presented. The unclad portion of a multi-mode optical fibre is coated with a pH sensitive dye, which is immobilized by the sol–gel route. The sensitivity of the device has been found to increase when multiple sol–gel coatings are used as the sensing region. The dynamic range and the temporal response of the sensor are investigated for two different dyes, namely bromocresol purple and bromocresol green. The performance of the device is evaluated in terms of the results obtained during actual measurements. |
URI: | http://dyuthi.cusat.ac.in/purl/2404 |
Files | Size |
---|---|
Dyuthi-P0226.pdf | (120.1Kb) |
Abstract: | The fabrication and characterization of a fibre optic pH sensor based on evanescent wave absorption is presented. The unclad portion of a multi-mode optical fibre is coated with a pH sensitive dye, which is immobilized by the sol–gel route. The sensitivity of the device has been found to increase when multiple sol–gel coatings are used as the sensing region. The dynamic range and the temporal response of the sensor are investigated for two different dyes, namely bromocresol purple and bromocresol green. The performance of the device is evaluated in terms of the results obtained during actual measurements. |
URI: | http://dyuthi.cusat.ac.in/purl/1771 |
Files | Size |
---|---|
A sensitive fib ... tiple sol-gel coatings.pdf | (106.3Kb) |
Abstract: | The fabrication and characterization of a fibre optic pH sensor based on evanescent wave absorption is presented. The unclad portion of a multi-mode optical fibre is coated with a pH sensitive dye, which is immobilized by the sol–gel route. The sensitivity of the device has been found to increase when multiple sol–gel coatings are used as the sensing region. The dynamic range and the temporal response of the sensor are investigated for two different dyes, namely bromocresol purple and bromocresol green. The performance of the device is evaluated in terms of the results obtained during actual measurements |
URI: | http://dyuthi.cusat.ac.in/purl/1772 |
Files | Size |
---|---|
A sensitive fib ... tiple sol-gel coatings.pdf | (106.3Kb) |
Abstract: | The fabrication and characterization of a fibre optic pH sensor based on evanescent wave absorption is presented. The unclad portion of a multi-mode optical fibre is coated with a pH sensitive dye, which is immobilized by the sol–gel route. The sensitivity of the device has been found to increase when multiple sol–gel coatings are used as the sensing region. The dynamic range and the temporal response of the sensor are investigated for two different dyes, namely bromocresol purple and bromocresol green. The performance of the device is evaluated in terms of the results obtained during actual measurements |
URI: | http://dyuthi.cusat.ac.in/purl/1773 |
Files | Size |
---|---|
A sensitive fib ... tiple sol-gel coatings.pdf | (106.3Kb) |
Abstract: | The study was carried out to understand the effect of silver-silica nanocomposite (Ag-SiO2NC) on the cell wall integrity, metabolism and genetic stability of Pseudomonas aeruginosa, a multiple drugresistant bacterium. Bacterial sensitivity towards antibiotics and Ag-SiO2NC was studied using standard disc diffusion and death rate assay, respectively. The effect of Ag-SiO2NC on cell wall integrity was monitored using SDS assay and fatty acid profile analysis while the effect on metabolism and genetic stability was assayed microscopically, using CTC viability staining and comet assay, respectively. P. aeruginosa was found to be resistant to β-lactamase, glycopeptidase, sulfonamide, quinolones, nitrofurantoin and macrolides classes of antibiotics. Complete mortality of the bacterium was achieved with 80 μgml-1 concentration of Ag-SiO2NC. The cell wall integrity reduced with increasing time and reached a plateau of 70 % in 110 min. Changes were also noticed in the proportion of fatty acids after the treatment. Inside the cytoplasm, a complete inhibition of electron transport system was achieved with 100 μgml-1 Ag-SiO2NC, followed by DNA breakage. The study thus demonstrates that Ag-SiO2NC invades the cytoplasm of the multiple drug-resistant P. aeruginosa by impinging upon the cell wall integrity and kills the cells by interfering with electron transport chain and the genetic stability |
Description: | Letters in applied microbiology, vol.56; 2012; 57-62 |
URI: | http://dyuthi.cusat.ac.in/purl/4420 |
Files | Size |
---|---|
Sequential inte ... ic resistant bacterium.pdf | (809.8Kb) |
Abstract: | The technique of reinforcing soil for foundation improvement is well established. This paper addresses the aspect of settlement of reinforced sand foundations, where the major part of the existing work deals with the aspect of bearing capacity. A detailed analysis is made paying individual attention to soil, reinforcement, and the interface between the two. A three-dimensional, nonlinear finite-element analysis is presented that uses a three-dimensional, nonlinear soil-reinforcement interface friction element, along with other threedimensional elements to model the system. The results of the analysis are compared with those from tests conducted in the laboratory and are found to be in good agreement. The studies lead to a better understanding of the behavior of the system at different stages of loading |
Description: | J. Geotech. Geoenviron. Eng. 1997.123:818-827. |
URI: | http://dyuthi.cusat.ac.in/purl/4305 |
Files | Size |
---|---|
Settlement Of Reinforced Sand In Foundations.pdf | (1.070Mb) |
Abstract: | The 2,4,6-triphenylthiapyrylium ion has been obtained imprisoned inside the supercages of the tridirectional, large pore zeolites Y and beta via ship-in-a-bottle synthesis from chalcone and acetophenone in the presence of hydrogen sulfide. The resulting solids are efficient and robust photocatalysts that are able to degrade phenol and aniline in water with a higher efficiency than the P-25 TiO2 standard. Preliminary tests have shown that these encapsulated dye materials are also efficient photocatalysts for the oxidative degradation of malodorous sulfurcontaining molecules. |
URI: | http://dyuthi.cusat.ac.in/purl/697 |
Files | Size |
---|---|
paper2.pdf | (174.6Kb) |
Abstract: | Polystyrene beads, impregnated with mineral salts/glutamine medium as inert support, were used to produce L-glutaminase from Vibrio costicola by solid-state fermentation. Maximum enzyme yield, 88 U/g substrate, was after 36 h. Glucose at 10 g/kg enhanced the enzyme yield by 66%. The support system allowed glutaminase to be recovered with higher specific activity and lower viscosity than when a wheat-bran system was used |
Description: | World Journal of Microbiology & Biotechnology 11,683-684 |
URI: | http://dyuthi.cusat.ac.in/purl/4246 |
Files | Size |
---|---|
Polystyrene-an ... lld-state fermentation.pdf | (138.6Kb) |
Abstract: | Short fiber reinforced thermoplastics have generated much interest these days since fibrous materials tend to increase both mechanical and thermal properties, such as tensile strength, flexural strength, flexural modulus, heat deflection temperature, creep resistance, and some times impact strength of thermoplastics. If the matrix and reinforcement are both based on polymers the composite are recyclable. The rheological behavior of recyclable composites based on nylon fiber reinforced polypropylene (PP) is reported in this paper. The rheological behavior was evaluated both using a capillary rheometer and a torque rheometer. The study showed that the composite became pseudoplastic with fiber content and hence fiber addition did not affect processing adversely at higher shear rates. The torque rheometer data resembled that obtained from the capillary rheometer. The energy of mixing and activation energy of mixing also did not show much variation from that of PP alone. |
URI: | http://dyuthi.cusat.ac.in/xmlui/purl/1999 |
Files | Size |
---|---|
Short nylon fibre....pdf | (438.5Kb) |
Abstract: | Short term load forecasting is one of the key inputs to optimize the management of power system. Almost 60-65% of revenue expenditure of a distribution company is against power purchase. Cost of power depends on source of power. Hence any optimization strategy involves optimization in scheduling power from various sources. As the scheduling involves many technical and commercial considerations and constraints, the efficiency in scheduling depends on the accuracy of load forecast. Load forecasting is a topic much visited in research world and a number of papers using different techniques are already presented. The accuracy of forecast for the purpose of merit order dispatch decisions depends on the extent of the permissible variation in generation limits. For a system with low load factor, the peak and the off peak trough are prominent and the forecast should be able to identify these points to more accuracy rather than minimizing the error in the energy content. In this paper an attempt is made to apply Artificial Neural Network (ANN) with supervised learning based approach to make short term load forecasting for a power system with comparatively low load factor. Such power systems are usual in tropical areas with concentrated rainy season for a considerable period of the year |
Description: | Power, Signals, Controls and Computation (EPSCICON), 2012 International Conference on |
URI: | http://dyuthi.cusat.ac.in/purl/4488 |
Files | Size |
---|---|
Short-Term Load ... ive Learning Algorithm.pdf | (978.7Kb) |
Abstract: | Two-photon excited (TPE) side illumination fluorescence studies in a Rh6G-RhB dye mixture doped polymer optical fiber (POF) and the effect of energy transfer on the attenuation coefficient is reported. The dye doped POF is pumped sideways using 800 nm, 70 fs laser pulses from a Ti:sapphire laser, and the TPE fluorescence emission is collected from the end of the fiber for different propagation distances. The fluorescence intensity of RhB doped POF is enhanced in the presence of Rh6G as a result of energy transfer from Rh6G to RhB. Because of the reabsorption and reemission process in dye molecules, an effective energy transfer is observed from the shorter wavelength part of the fluorescence spectrum to the longer wavelength part as the propagation distance is increased in dye doped POF. An energy transfer coefficient is found to be higher at shorter propagation distances compared to longer distances. A TPE fluorescence signal is used to characterize the optical attenuation coefficient in dye doped POF. The attenuation coefficient decreases at longer propagation distances due to the reabsorption and reemission process taking place within the dye doped fiber as the propagation distance is increased. |
URI: | http://dyuthi.cusat.ac.in/purl/2475 |
Files | Size |
---|---|
Dyuthi-P0273.pdf | (1.014Mb) |
Abstract: | The aim of this study is to show the importance of two classification techniques, viz. decision tree and clustering, in prediction of learning disabilities (LD) of school-age children. LDs affect about 10 percent of all children enrolled in schools. The problems of children with specific learning disabilities have been a cause of concern to parents and teachers for some time. Decision trees and clustering are powerful and popular tools used for classification and prediction in Data mining. Different rules extracted from the decision tree are used for prediction of learning disabilities. Clustering is the assignment of a set of observations into subsets, called clusters, which are useful in finding the different signs and symptoms (attributes) present in the LD affected child. In this paper, J48 algorithm is used for constructing the decision tree and K-means algorithm is used for creating the clusters. By applying these classification techniques, LD in any child can be identified |
URI: | http://dyuthi.cusat.ac.in/purl/4192 |
Files | Size |
---|---|
Significance Of ... Learning Disabilities.pdf | (200.4Kb) |
Abstract: | Filled and gum compounds of Isobutylene-Isoprene rubber were extruded through a laboratory extruder at various feeding rates, different temperatures and revolutions per minute. The extruded compounds were vulcanized up to their optimum cure times and the mechanical properties of the vulcanizates were determined. The properties suggest that there is a particular feeding rate in the starved fed region, which results in maximum mechanical properties. The study shows that running the extruder at a slightly starved condition is an attractive means of improving the physical properties. |
URI: | http://dyuthi.cusat.ac.in/purl/864 |
Files | Size |
---|---|
P J Joseph Fran ... icance of..,Dec1996PDF.PDF | (6.623Mb) |
Abstract: | Cattle feed industry is a major segment of animal feed industry. This industry is gradually evolving into an organized sector and the feed manufactures are increasingly using modern and sophisticated methods that seek to incorporate best global practices. This industry has got high potential for growth in India, given the fact that the country is the world’s leading producer of milk and its production is expected to grow at a compounded annual growth rate of 4 per cent. Besides, the concept of branded cattle feed as a packaged commodity is fast gaining popularity in rural India. There can be a positive change in the demand for cattle feed because of factors like (i) shrinkage of open land for cattle grazing, urbanization and resultant shortage of conventionally used cattle feeds, and (ii) introduction of high yield cattle requires specialized feeds. Earlier research studies done by the present authors have revealed the significant growth prospects of the branded cattle feed industry, the feed consumption pattern and the relatively high share of branded feeds, feed consumption pattern based on product types (like, pellet and mash), composition of cattle feed market and the relatively large shares of Kerala Feeds Ltd. (KFL) and Kerala Solvent Extractions Ltd. (KSE) brands, the major factors influencing the purchasing decisions etc. As a continuation of the earlier studies, this study makes a closer look into the significance of product types in the buyer behavior, level of awareness about the brand and its implications on purchasing decisions, and the brandshifting behavior and its determinants |
Description: | International Journal of Business and Administration Research Review, Vol.2, Issue.4, Jan-March, 2014 |
URI: | http://dyuthi.cusat.ac.in/purl/4586 |
Files | Size |
---|---|
Significance Of ... irical Study In Kerala.pdf | (156.8Kb) |
Abstract: | There are a large number of agronomic-ecological interactions that occur in a world with increasing levels of CO2, higher temperatures and a more variable climate. Climate change and the associated severe problems will alter soil microbial populations and diversity. Soils supply many atmospheric green house gases by performing as sources or sinks. The most important of these gases include CH4, CO2 and N2O. Most of the green house gases production and consumption processes in soil are probably due to microorganisms. There is strong inquisitiveness to store carbon (C) in soils to balance global climate change. Microorganisms are vital to C sequestration by mediating putrefaction and controlling the paneling of plant residue-C between CO2 respiration losses or storage in semi-permanent soil-C pools. Microbial population groups and utility can be manipulated or distorted in the course of disturbance and C inputs to either support or edge the retention of C. Fungi play a significant role in decomposition and appear to produce organic matter that is more recalcitrant and favor long-term C storage and thus are key functional group to focus on in developing C sequestration systems. Plant residue chemistry can influence microbial communities and C loss or flow into soil C pools. Therefore, as research takings to maximize C sequestration for agricultural and forest ecosystems - moreover plant biomass production, similar studies should be conducted on microbial communities that considers the environmental situations |
Description: | Indian J. Edu. Inf. Manage., Vol. 1, No. 3 (Mar 2012) |
URI: | http://dyuthi.cusat.ac.in/purl/3947 |
Files | Size |
---|---|
Significance of ... ence to climate change.pdf | (298.8Kb) |
Dyuthi Digital Repository Copyright © 2007-2011 Cochin University of Science and Technology. Items in Dyuthi are protected by copyright, with all rights reserved, unless otherwise indicated.