| Abstract: | Aim of the present work was to automate CSP process, to deposit and characterize CuInS2/In2S3 layers using this system and to fabricate devices using these films.An automated spray system for the deposition of compound semiconductor thin films was designed and developed so as to eliminate the manual labour involved in spraying and facilitate standardization of the method. The system was designed such that parameters like spray rate, movement of spray head, duration of spray, temperature of substrate, pressure of carrier gas and height of the spray head from the substrate could be varied. Using this system, binary, ternary as well as quaternary films could be successfully deposited.The second part of the work deal with deposition and characterization of CuInS2 and In2S3 layers respectively.In the case of CuInS2 absorbers, the effects of different preparation conditions and post deposition treatments on the optoelectronic, morphological and structural properties were investigated. It was observed that preparation conditions and post deposition treatments played crucial role in controlling the properties of the films. The studies in this direction were useful in understanding how the variation in spray parameters tailored the properties of the absorber layer. These results were subsequently made use of in device fabrication process.Effects of copper incorporation in In2S3 films were investigated to find how the diffusion of Cu from CuInS2 to In2S3 will affect the properties at the junction. It was noticed that there was a regular variation in the opto-electronic properties with increase in copper concentration.Devices were fabricated on ITO coated glass using CuInS2 as absorber and In2S3 as buffer layer with silver as the top electrode. Stable devices could be deposited over an area of 0.25 cm2, even though the efficiency obtained was not high. Using manual spray system, we could achieve devices of area 0.01 cm2 only. Thus automation helped in obtaining repeatable results over larger areas than those obtained while using the manual unit. Silver diffusion on the cells before coating the electrodes resulted in better collection of carriers.From this work it was seen CuInS2/In2S3 junction deposited through automated spray process has potential to achieve high efficiencies. |
| Description: | Department of Physics, Cochin University of Science and Technology |
| URI: | http://dyuthi.cusat.ac.in/xmlui/purl/1954 |
| Files | Size |
|---|---|
| Dyuthi-T0377.pdf | (2.826Mb) |
| URI: | http://dyuthi.cusat.ac.in/purl/5492 |
| Files | Size |
|---|---|
| Dyuthi T-2534.pdf | (8.311Mb) |
| Description: | Department of Hindi, Cochin University of Science and Technology |
| URI: | http://dyuthi.cusat.ac.in/xmlui/purl/1940 |
| Files | Size |
|---|---|
| Dyuthi-T0378.pdf | (1.569Mb) |
| Abstract: | Hindi |
| Description: | Department of Hindi, Cochin University of Science and Technology |
| URI: | http://dyuthi.cusat.ac.in/purl/4825 |
| Files | Size |
|---|---|
| Dyuthi-T1922.pdf | (5.350Mb) |
| URI: | http://dyuthi.cusat.ac.in/purl/5220 |
| Files | Size |
|---|---|
| Dyuthi T-2255.pdf | (13.16Mb) |
| Abstract: | This thesis Entitled Bayesian inference in Exponential and pareto populations in the presence of outliers. The main theme of the present thesis is focussed on various estimation problems using the Bayesian appraoch, falling under the general category of accommodation procedures for analysing Pareto data containing outlier. In Chapter II. the problem of estimation of parameters in the classical Pareto distribution specified by the density function. In Chapter IV. we discuss the estimation of (1.19) when the sample contain a known number of outliers under three different data generating mechanisms, viz. the exchangeable model. Chapter V the prediction of a future observation based on a random sample that contains one contaminant. Chapter VI is devoted to the study of estimation problems concerning the exponential parameters under a k-outlier model. |
| Description: | Department of Mathematics and Statistics, Cochin University of Science and Technoloy |
| URI: | http://dyuthi.cusat.ac.in/purl/3066 |
| Files | Size |
|---|---|
| Dyuthi-T1040.pdf | (4.788Mb) |
| URI: | http://dyuthi.cusat.ac.in/purl/1851 |
| Files | Size |
|---|---|
| Dyuthi-T0059.pdf | (4.162Mb) |
| Abstract: | ACCURATE sensing of vehicle position and attitude is still a very challenging problem in many mobile robot applications. The mobile robot vehicle applications must have some means of estimating where they are and in which direction they are heading. Many existing indoor positioning systems are limited in workspace and robustness because they require clear lines-of-sight or do not provide absolute, driftfree measurements.The research work presented in this dissertation provides a new approach to position and attitude sensing system designed specifically to meet the challenges of operation in a realistic, cluttered indoor environment, such as that of an office building, hospital, industrial or warehouse. This is accomplished by an innovative assembly of infrared LED source that restricts the spreading of the light intensity distribution confined to a sheet of light and is encoded with localization and traffic information. This Digital Infrared Sheet of Light Beacon (DISLiB) developed for mobile robot is a high resolution absolute localization system which is simple, fast, accurate and robust, without much of computational burden or significant processing. Most of the available beacon's performance in corridors and narrow passages are not satisfactory, whereas the performance of DISLiB is very encouraging in such situations. This research overcomes most of the inherent limitations of existing systems.The work further examines the odometric localization errors caused by over count readings of an optical encoder based odometric system in a mobile robot due to wheel-slippage and terrain irregularities. A simple and efficient method is investigated and realized using an FPGA for reducing the errors. The detection and correction is based on redundant encoder measurements. The method suggested relies on the fact that the wheel slippage or terrain irregularities cause more count readings from the encoder than what corresponds to the actual distance travelled by the vehicle.The application of encoded Digital Infrared Sheet of Light Beacon (DISLiB) system can be extended to intelligent control of the public transportation system. The system is capable of receiving traffic status input through a GSM (Global System Mobile) modem. The vehicles have infrared receivers and processors capable of decoding the information, and generating the audio and video messages to assist the driver. The thesis further examines the usefulness of the technique to assist the movement of differently-able (blind) persons in indoor or outdoor premises of his residence.The work addressed in this thesis suggests a new way forward in the development of autonomous robotics and guidance systems. However, this work can be easily extended to many other challenging domains, as well. |
| Description: | Department of Electronics, Cochin University of Science and Technology |
| URI: | http://dyuthi.cusat.ac.in/purl/2483 |
| Files | Size |
|---|---|
| Dyuthi-T0666.pdf | (13.00Mb) |
| Abstract: | In the present thesis, possibility of beam shaping of sectoral horns and corner reflector systems'has been studied in detail. The experimental results obtained in the above two cases are compared. As far as the flanged sectoral horns are concerned, the special advantage is that the gain is increased without impairing impedance conditions. An intense study on corner reflector antennas shows that the been broadening or focussing will be possible by adjusting parameters involved. Beam tilting by imposing asymmetries is another interesting property of the systems. A comprehensive study of these fields has been presented in Chapter II. Chapter III is exclusively for describing the experimental techniques used in the present investigation. In Chapter IV, experimental results on flanged sectoral horns and corner reflector eyetses are presented. A comparative analysis of the experimental results obtained with flanged sectoral horns and corner reflector systems is presented in the Chapter V. The similarity and close resemblance in each aspects are shown by presenting typical results from these two eysteee. Theoretical aspects of both types of antennas are considered in Chapter VI. Attempts are made for co-ordinating the theoretical aspects and drawing a final conclusion. In Chapter VII. the final conclusion that the flanged sectoral horn may be considered as a corner reflector system has been drawn. The importance of the conclusions and usefulness are pointed out. The scope for further work in these lines has been indicated. |
| Description: | Department of physics, Cochin University of Science And Technology |
| URI: | http://dyuthi.cusat.ac.in/purl/3291 |
| Files | Size |
|---|---|
| Dyuthi-T1273.pdf | (7.116Mb) |
| Abstract: | The research in the area of geopolymer is gaining momentum during the past 20 years. Studies confirm that geopolymer concrete has good compressive strength, tensile strength, flexural strength, modulus of elasticity and durability. These properties are comparable with OPC concrete.There are many occasions where concrete is exposed to elevated temperatures like fire exposure from thermal processor, exposure from furnaces, nuclear exposure, etc.. In such cases, understanding of the behaviour of concrete and structural members exposed to elevated temperatures is vital. Even though many research reports are available about the behaviour of OPC concrete at elevated temperatures, there is limited information available about the behaviour of geopolymer concrete after exposure to elevated temperatures. A preliminary study was carried out for the selection of a mix proportion. The important variable considered in the present study include alkali/fly ash ratio, percentage of total aggregate content, fine aggregate to total aggregate ratio, molarity of sodium hydroxide, sodium silicate to sodium hydroxide ratio, curing temperature and curing period. Influence of different variables on engineering properties of geopolymer concrete was investigated. The study on interface shear strength of reinforced and unreinforced geopolymer concrete as well as OPC concrete was also carried out. Engineering properties of fly ash based geopolymer concrete after exposure to elevated temperatures (ambient to 800 °C) were studied and the corresponding results were compared with those of conventional concrete. Scanning Electron Microscope analysis, Fourier Transform Infrared analysis, X-ray powder Diffractometer analysis and Thermogravimetric analysis of geopolymer mortar or paste at ambient temperature and after exposure to elevated temperature were also carried out in the present research work. Experimental study was conducted on geopolymer concrete beams after exposure to elevated temperatures (ambient to 800 °C). Load deflection characteristics, ductility and moment-curvature behaviour of the geopolymer concrete beams after exposure to elevated temperatures were investigated. Based on the present study, major conclusions derived could be summarized as follows. There is a definite proportion for various ingredients to achieve maximum strength properties. Geopolymer concrete with total aggregate content of 70% by volume, ratio of fine aggregate to total aggregate of 0.35, NaOH molarity 10, Na2SiO3/NaOH ratio of 2.5 and alkali to fly ash ratio of 0.55 gave maximum compressive strength in the present study. An early strength development in geopolymer concrete could be achieved by the proper selection of curing temperature and the period of curing. With 24 hours of curing at 100 °C, 96.4% of the 28th day cube compressive strength could be achieved in 7 days in the present study. The interface shear strength of geopolymer concrete is lower to that of OPC concrete. Compared to OPC concrete, a reduction in the interface shear strength by 33% and 29% was observed for unreinforced and reinforced geopolymer specimens respectively. The interface shear strength of geopolymer concrete is lower than ordinary Portland cement concrete. The interface shear strength of geopolymer concrete can be approximately estimated as 50% of the value obtained based on the available equations for the calculation of interface shear strength of ordinary portland cement concrete (method used in Mattock and ACI). Fly ash based geopolymer concrete undergoes a high rate of strength loss (compressive strength, tensile strength and modulus of elasticity) during its early heating period (up to 200 °C) compared to OPC concrete. At a temperature exposure beyond 600 °C, the unreacted crystalline materials in geopolymer concrete get transformed into amorphous state and undergo polymerization. As a result, there is no further strength loss (compressive strength, tensile strength and modulus of elasticity) in geopolymer concrete, whereas, OPC concrete continues to lose its strength properties at a faster rate beyond a temperature exposure of 600 °C. At present no equation is available to predict the strength properties of geopolymer concrete after exposure to elevated temperatures. Based on the study carried out, new equations have been proposed to predict the residual strengths (cube compressive strength, split tensile strength and modulus of elasticity) of geopolymer concrete after exposure to elevated temperatures (upto 800 °C). These equations could be used for material modelling until better refined equations are available. Compared to OPC concrete, geopolymer concrete shows better resistance against surface cracking when exposed to elevated temperatures. In the present study, while OPC concrete started developing cracks at 400 °C, geopolymer concrete did not show any visible cracks up to 600 °C and developed only minor cracks at an exposure temperatureof 800 °C. Geopolymer concrete beams develop crack at an early load stages if they are exposed to elevated temperatures. Even though the material strength of the geopolymer concrete does not decrease beyond 600 °C, the flexural strength of corresponding beam reduces rapidly after 600 °C temperature exposure, primarily due to the rapid loss of the strength of steel. With increase in temperature, the curvature at yield point of geopolymer concrete beam increases and thereby the ductility reduces. In the present study, compared to the ductility at ambient temperature, the ductility of geopolymer concrete beams reduces by 63.8% at 800 °C temperature exposure. Appropriate equations have been proposed to predict the service load crack width of geopolymer concrete beam exposed to elevated temperatures. These equations could be used to limit the service load on geopolymer concrete beams exposed to elevated temperatures (up to 800 °C) for a predefined crack width (between 0.1mm and 0.3 mm) or vice versa. The moment-curvature relationship of geopolymer concrete beams at ambient temperature is similar to that of RCC beams and this could be predicted using strain compatibility approach Once exposed to an elevated temperature, the strain compatibility approach underestimates the curvature of geopolymer concrete beams between the first cracking and yielding point. |
| Description: | Division of Safety and Fire Engineering |
| URI: | http://dyuthi.cusat.ac.in/purl/5030 |
| Files | Size |
|---|---|
| Dyuthi-T2097.pdf | (5.482Mb) |
| Abstract: | This study aims to analyze, compare and contrast the behavioral competency of officials in commercial banks headquartered in Kerala. This is done by analyzing the soft skills/behavioral skills possessed by an individual employee in both clerical and managerial levels and the means adopted to enhance their said skills in near future. The study was conducted with the objective of analyzing the behavioral competency of the managers and clerical staff in the commercial banks headquartered in Kerala. The researcher has gone through the available literature with respect to employee competency, job satisfaction and employee performance evaluation to formulate the problem and conceptualize the framework of the study. The study concluded that the competency of the employees differs from one bank to the other but strengthening the employees’ competency is the only possible solution by which the banks can determine their future growth prospects. Only through competency, banks can achieve high level of performance especially under the globalised situation. |
| URI: | http://dyuthi.cusat.ac.in/purl/4997 |
| Files | Size |
|---|---|
| Dyuthi-T2066.pdf | (4.464Mb) |
| URI: | http://dyuthi.cusat.ac.in/purl/5482 |
| Files | Size |
|---|---|
| Dyuthi T-2524.pdf | (12.00Mb) |
| Abstract: | Concrete is a universal material in the construction industry. With natural resources like sand and aggregate, fast depleting, it is time to look for alternate materials to substitute these in the process of making concrete. There are instances like exposure to solar radiation, fire, furnaces, and nuclear reactor vessels, special applications like missile launching pads etc., where concrete is exposed to temperature variations In this research work, an attempt has been made to understand the behaviour of concrete when weathered laterite aggregate is used in both conventional and self compacting normal strength concrete. The study has been extended to understand the thermal behaviour of both types of laterised concretes and to check suitability as a fire protection material. A systematic study of laterised concrete considering parameters like source of laterite aggregate, grades of Ordinary Portland Cement (OPC) and types of supplementary cementitious materials (fly ash and GGBFS) has been carried out to arrive at a feasible combination of various ingredients in laterised concrete. A mix design methodology has been proposed for making normal strength laterised self compacting concrete based on trial mixes and the same has also been validated. The physical and mechanical properties of laterised concretes have been studied with respect to different variables like exposure temperature (200°C, 400°C and 600°C) and cooling environment (air cooled and water cooled). The behaviour of ferrocement elements with laterised self compacting concrete has also been studied by varying the cover to mesh reinforcement (10mm to 50mm at an interval of 10mm), exposure temperature and cooling environment. |
| Description: | Division of Safety and Fire Engineering School of Engineering,Cochin University of Science and Technology. |
| URI: | http://dyuthi.cusat.ac.in/purl/3262 |
| Files | Size |
|---|---|
| Dyuthi-T1236.pdf | (4.324Mb) |
| Abstract: | Myocardial ischemia is caused by the inadequate supply of blood to the myocardium usually as a result of coronary artery disease. Cardiovascular disease is the leading cause of death worldwide and coronary artery disease is the greatest contributor, with 7.5 million deaths annually. Currently available drugs are able to alleviate the symptoms but have undesirable effects and secondary complications. Tribulus terrestris L. root and fruit are used in Ayurveda to treat heart ailments. But a scientific validation of the protective property of the herb against myocardial ischemia and the mechanism by which Tribulus terrestris L. mediates the protection has not been carried out. The objective of the present thesis is to elucidate the molecular mechanism of the beneficial property of Tribulus terrestris L. fruit and root against myocardial ischemia and cardiac dysfunctions by employing in vitro and in vivo models. |
| URI: | http://dyuthi.cusat.ac.in/purl/5172 |
| Files | Size |
|---|---|
| Dyuthi-T2207.pdf | (5.360Mb) |
| URI: | http://dyuthi.cusat.ac.in/purl/5480 |
| Files | Size |
|---|---|
| Dyuthi T-2522.pdf | (18.29Mb) |
| Abstract: | The thesis on the"Benthic ecology of selected prawn culture fields and ponds near Cochin” was taken up with a view to provide information on the qualitative and quantitative distribution of benthos and their relationships to prawnproduction of different culture ecosystems and to the physico-chemical parameters influencing their production. A two-year observation was carried out in nine selected prawn culture systems including perennial ponds (stations 1 to 4) seasonal fields (stations 5 to 7) and contiguous canals (stations 8 and 9) during December 1988 to November 1989. All macro- and meiobenthic organisms contributing to the faua were identified and their abundance, distribution, diversity, biomass and trophic relationships between benthos and prawns were studied. The environmental variables studied were temperature pH, salinity, dissolved oxygen, alkalinity, nitrite-nitrogen, nitrate-nitrogen, amonianitrogen, phosphate and silicate of bottom water and organic carbon and texture of the soil The thesis is presented in 4 Chapters. Chapter I presents an’ INTRODUCTION to the topic of study and a review of relevant works to bring an awareness to the present status of research in benthos and benthic ecology. Chapter 11, MATERIALS AND MTHODS, includes the techniques of sampling, preservation of samples and methods of analyses of various physico-chemical factors and area covered under the study is also given in this chapter. Chapter III, HYDROGRAPHY deals with the results of investigation and discussion onthe physico-chemical parameters of water and Chapter IV, SEDIMENT covers the sedimentoloical characteristics of the different culture systems followed by a detailed discussion. Chapter V, BOTTOM FAUNA presents an account on the various aspects of benthos and benthic ecology and the details of prawn production. A discussion on the overall assessment of interrelations between abiotic and biotic factors is given in Chapter VI, DISCUSSION. A critical evaluation of the implication of benthic production on prawn production under culture conditions and trophic relationships are also included in this chapter. An executive SUMMARY of the observations made during this study is presented in the final section of the thesis . |
| Description: | Central Marine Fisheries Research Institute |
| URI: | http://dyuthi.cusat.ac.in/purl/3224 |
| Files | Size |
|---|---|
| Dyuthi-T1198.pdf | (3.508Mb) |
Dyuthi Digital Repository Copyright © 2007-2011 Cochin University of Science and Technology. Items in Dyuthi are protected by copyright, with all rights reserved, unless otherwise indicated.