| Abstract: | Invertase was immobilized on acid activated montmorillonite via two independent procedures, adsorption and covalent binding. The immobilized enzymes were characterized by XRD, NMR and N2 adsorption measurements and their activity was tested in a fixed bed reactor. XRD revealed that the enzyme was situated on the periphery of the clay and the side chains of different amino acid residues were involved in intercalation with the clay matrix. NMR demonstrated that tetrahedral Al was linked to the enzyme during adsorption and the octahedral Al was involved during covalent binding. Secondary interaction of the enzyme with Al was also observed. N2 adsorption studies showed that covalent binding of enzymes caused pore blockage since the highly polymeric species were located at the pore entrance. The fixed bed reactor proved to be efficient for the immobilized invertase. The optimum pH and pH stability improved upon immobilization. The kinetic parameters calculated also showed an enhanced efficiency of the immobilized systems. They could be used continuously for long period. Covalently bound invertase demonstrated greater operational stability. |
| URI: | http://dyuthi.cusat.ac.in/purl/2270 |
| Files | Size |
|---|---|
| Dyuthi-SS60.pdf | (481.4Kb) |
| Abstract: | Glucoamylase was immobilized on acid activated montmorillonite clay via two different procedures namely adsorption and covalent binding. The immobilized enzymes were characterized by XRD, NMR and N2 adsorption measurements and the activity of immobilized glucoamylase for starch hydrolysis was determined in a batch reactor. XRD shows intercalation of enzyme into the clay matrix during both immobilization procedures. Intercalation occurs via the side chains of the amino acid residues, the entire polypeptide backbone being situated at the periphery of the clay matrix. 27Al NMR studies revealed the different nature of interaction of enzyme with the support for both immobilization techniques. N2 adsorption measurements indicated a sharp drop in surface area and pore volume for the covalently bound glucoamylase that suggested severe pore blockage. Activity studies were performed in a batch reactor. The adsorbed and covalently bound glucoamylase retained 49% and 66% activity of the free enzyme respectively. They showed enhanced pH and thermal stabilities. The immobilized enzymes also followed Michaelis–Menten kinetics. Km was greater than the free enzyme that was attributed to an effect of immobilization. The immobilized preparations demonstrated increased reusability as well as storage stability. |
| URI: | http://dyuthi.cusat.ac.in/purl/2259 |
| Files | Size |
|---|---|
| Dyuthi-SS51.pdf | (248.5Kb) |
| Abstract: | Glucoamylase from Aspergillus Niger was immobilized on montmorillonite clay (K-10) by two procedures, adsorption and covalent binding. The immobilized enzymes were characterized using XRD, surface area measurements and 27Al MAS NMR and the activity of the immobilized enzymes for starch hydrolysis was tested in a fixed bed reactor (FBR). XRD shows that enzyme intercalates into the inter-lamellar space of the clay matrix with a layer expansion up to 2.25 nm. Covalently bound glucoamylase demonstrates a sharp decrease in surface area and pore volume that suggests binding of the enzyme at the pore entrance. NMR studies reveal the involvement of octahedral and tetrahedral Al during immobilization. The performance characteristics in FBR were evaluated. Effectiveness factor (η) for FBR is greater than unity demonstrating that activity of enzyme is more than that of the free enzyme. The Michaelis constant (Km) for covalently bound glucoamylase was lower than that for free enzyme, i.e., the affinity for substrate improves upon immobilization. This shows that diffusional effects are completely eliminated in the FBR. Both immobilized systems showed almost 100% initial activity after 96 h of continuous operation. Covalent binding demonstrated better operational stability. |
| URI: | http://dyuthi.cusat.ac.in/purl/2316 |
| Files | Size |
|---|---|
| Dyuthi-SS84.pdf | (422.1Kb) |
| Abstract: | The effect of residual cations in rare earth metal modified faujasite–Y zeolite has been monitored using magic angle spinning NMR spectral analysis and catalytic activity studies. The second metal ions being used are Na+, K+ and Mg+. From a comparison of the spectra of different samples, it is concluded that potassium and magnesium exchange causes a greater downfield shift in the 29Si NMR peaks. Also, lanthanum exchanged samples show migration behavior from large cages to small cages, which causes the redistribution of second counter cations. It is also observed that Mg2+ causes the most effective migration of lanthanum ions due to its greater charge. The prepared systems were effectively employed for the alkylation of benzene with 1-octene in the vapor phase. From the deactivation studies it is observed that the as-exchanged zeolites possess better stability towards reaction condition over the pure HFAU zeolite. |
| URI: | http://dyuthi.cusat.ac.in/purl/2314 |
| Files | Size |
|---|---|
| Dyuthi-SS82.pdf | (816Kb) |
| Abstract: | The present work attempts a systematic examination of the effect of sulphate content on the physico-chemical properties and catalytic activity of sulphated zirconia and iron promoted sulphated zirconia systems. Sulphate content is estimated by EDX analysis. The amount of sulphate incorporated has been found to influence the surface area, crystal structure and the acid strength distribution. Ammonia TPD and adsorption studies using perylene have enabled the determination of surface acidic properties. The results are supported by the thermodesorption studies using pyridine and 2,6-dimethylpyridine. The catalytic activity towards benzoylation reaction has been correlated with the surface acidity of the systems. |
| URI: | http://dyuthi.cusat.ac.in/purl/2281 |
| Files | Size |
|---|---|
| Dyuthi-SS64.pdf | (1.319Mb) |
| Abstract: | Cyclohexanol decomposition activity of supported vanadia catalysts is ascribed to the high surface area, total acidity and interaction between supported vanadia and the amorphous support. Among the supported catalysts, the effect of vanadia over various wt% V2O5 (2–10) loading indicates that the catalyst comprising of 6 wt% V2O5 exhibits higher acidity and decomposition activity. Structural characterization of the catalysts has been done by techniques like energy dispersive X-ray analysis, X-ray diffraction and BET surface area. Acidity of the catalysts has been measured by temperature programmed desorption using ammonia as a probe molecule and the results have been correlated with the activity of catalysts. |
| URI: | http://dyuthi.cusat.ac.in/purl/2321 |
| Files | Size |
|---|---|
| Dyuthi-P00002.pdf | (380.1Kb) |
| Abstract: | Invertase was immobilised on microporous montmorillonite K-10 via adsorption and covalent binding. The immobilised enzymes were tested for sucrose hydrolysis activity in a batch reactor. Km for immobilised systems was greater than free enzyme. The immobilised forms could be reused for 15 continuous cycles without any loss in activity. After 25 cycles, 85% initial activity was retained. A study on leaching of enzymes showed that 100% enzyme was retained even after 15 cycles of reuse. Leaching increased with reaction temperature. Covalent binding resisted leaching even at temperatures of 70 °C. |
| URI: | http://dyuthi.cusat.ac.in/purl/2312 |
| Files | Size |
|---|---|
| Dyuthi-SS80.pdf | (185.0Kb) |
| Abstract: | The present work investigates on the applicability of metal promoted sulphated zirconia catalysts for the hydroxylation of phenol under mild conditions. The percentage conversion and product distribution was highly sensitive towards the reaction parameters like the catalyst composition, reaction temperature, H202/ phenol ratio and the solvent used. |
| URI: | http://dyuthi.cusat.ac.in/purl/2218 |
| Files | Size |
|---|---|
| Dyuthi-SS19.pdf | (643.1Kb) |
| Abstract: | The Lewis acidity of yttrium and dysprosium exchanged zeolite Y and ZSM-5 has been determined by titration method using Hammett indicators. The acidity of the Y form increases with increase in concentration of the rare earth cation in the Y zeolite. It is independent of the amount of the rare earth ion for ZSM-5. The data have been correlated with the activity of these zeolites for the esterification of butanol using acetic acid. |
| URI: | http://dyuthi.cusat.ac.in/purl/2310 |
| Files | Size |
|---|---|
| Dyuthi-SS77.pdf | (173.7Kb) |
| Abstract: | The present work undertakes the preparation and physico-chemical characterisation of iron promoted sulphated zirconia (SZ) with different amounts of iron loading and their application to Friedel-Crafts benzoylation of benzene, toluene and xylene under different experimental conditions, XRD and laser Raman techniques reveal the stabilisation of the tetragonal phase of zirconia and the existence of iron in highly dispersed form as Fe203 on the catalyst surface. The surface acidic properties were determined by ammonia temperature programmed desorption (TPD) and perylene adsorption, The results were supported by the TGA studies after adsorption of pyridine and 2,6-dimethylpyridine (2,6-DMP), Strong Lewis acid sites on the surface, which are evident from TPD and perylene adsorption studies. explain the high catalytic activity of the systems towards benzoylation. The experimental results provide evidence for the truly heterogeneous nature of the reaction. The studies also establish the resistance to deactivation in the metal incorporated sulphated systems. |
| URI: | http://dyuthi.cusat.ac.in/purl/2279 |
| Files | Size |
|---|---|
| Dyuthi-SS62.pdf | (696.8Kb) |
| Abstract: | Iron, aluminium and mixed iron aluminium pillared clays have been prepared by partial hydrolysis method and doped with IO% Mo, V and Cr. The samples have been characterised by XRD, FTIR and surface area and pore Volume measurements. The surface acid site distribution has been determined by temperature programmed desorption of ammonia. Vanadia incorporated systems show maximum acidity. Benzylation of o-xylene has been done as probe reaction to test catalytic activity. Benzyl chloride is a superior benzylating agent compared to benzyl alcohol in activity and selectivity. Cent percent selectivity towards monobenzylated product is obtained in all the cases. Fe pillared systems exhibit maximum activity. The catalytic activities of the systems can be correlated with the amount of strong add sites. The effects of various reaction variables on the reaction have been studied. Presence of moisture has a diminishing effect on the reaction rate. |
| URI: | http://dyuthi.cusat.ac.in/purl/2248 |
| Files | Size |
|---|---|
| Dyuthi-SS41.pdf | (593.7Kb) |
| Abstract: | The liquid-phase Friedel-Crafts acylation of toluene using benzoyl chloride as benzoylating agent has heen carried out over Nix, Mn(l-x)Fe2 O4 (x=O, 0.2, 0.4, 0.6, 0.8 and 1.0) type systems under different reaction conditions. It is observed that the systems with high 'x' values are effective for the conversion of BOC and the selective formation of 4-MBP. Selectivity for 4-MBP over MnFe2O4 is more than 90% under the optimized reaction conditions. Sites of moderate acidity is effective in calalyzing the benzoylation reaction. |
| URI: | http://dyuthi.cusat.ac.in/purl/2210 |
| Files | Size |
|---|---|
| Dyuthi-SS14.pdf | (504.4Kb) |
| Abstract: | A novel N4O coordination mode offers carbohydrazone ligands as a building block for interesting frameworks through self-assembly. Bridging mode of oxygen of bis(2-benzoylpyridine ketone) carbohydrazone (H2L) with metal centers facilitates the formation of the macrocyclic molecular square [Zn(HL)]4(BF4)4 · 10H2O, offers wide range of applications for carbohydrazones. |
| URI: | http://dyuthi.cusat.ac.in/xmlui/purl/2102 |
| Files | Size |
|---|---|
| Macrocyclic molecular square complex....pdf | (696.1Kb) |
| Abstract: | Kinetics of mercuric chloride catalysed solvolysis of benzyl chloride have been studied in water. 10% aq. ethanol, 10,20 and 30% aq. acetone and 20% aq. DMSO. The results confirm the operation of a mass law effect. |
| URI: | http://dyuthi.cusat.ac.in/purl/2224 |
| Files | Size |
|---|---|
| Dyuthi-SS28.pdf | (212.1Kb) |
| Abstract: | Knoevenagel condensation between carbonyl compounds and active methylene compounds as well as three component Mannich reaction between aldehydes, ketones and amines proceeded smoothly in water with good to excellent yield and high selectivity in the presence of zero and first generation poly(amidoamine) (PAMAM) dendrimers. The products and the catalyst were separated by simple biphasic extraction. The catalyst was found to be reusable. |
| URI: | http://dyuthi.cusat.ac.in/xmlui/purl/1967 |
| Files | Size |
|---|---|
| Organocatalysis by poly...pdf | (240.0Kb) |
| URI: | http://dyuthi.cusat.ac.in/xmlui/purl/1972 |
| Files | Size |
|---|---|
| K K M Yusuff,Organometallic Hydroxides ...pdf | (779.6Kb) |
| Abstract: | A series of supported vanadia systems have been prepared by excess solvent technique using La203 and DY203 as supports. Physical characterization has been carried out using XRD, FTIR, TG studies, BET surface area measurement, pore volume analysis etc. Cyclohexanol decomposition has been used as a test reaction for evaluating the acid base properties of the supported system. The oxidative dehydrogenation of ethylbenzene has been employed as a chemical probe reaction to examine the catalytic activity. The active species correspond to amorphous and crystalline tetrahedral vanadyl units in the supported system. |
| URI: | http://dyuthi.cusat.ac.in/purl/2211 |
| Files | Size |
|---|---|
| Dyuthi-SS13.pdf | (624.7Kb) |
| Abstract: | The thermal diffusivity of y-alumina is determined by the photoacoustic method. The method is calibrated by determining the thermal diffusivity of copper and aluminum. The effect of the chemisorbed hydroxyl groups or thermal diffusivity is studied by degassing the sample at different temperatures. |
| URI: | http://dyuthi.cusat.ac.in/purl/2276 |
| Files | Size |
|---|---|
| Dyuthi-SS37.pdf | (239.8Kb) |
| Abstract: | The heterogeneous photocatalytic degradation of methylorange over TiO2 is studied and is found to be cost effective. Effect of Zirconium metal incorporation over titania system is investigated. Photocatalytic degradation of methylorange using solar radiation is found to be highly economical when compared with the processes using artificial UV radiation, which require substantial electrical power input. The characterization of titania as well as modified zirconium metal doped titania systems are done using XRD, FTIR and EDAX measurements. The catalytic activities of different systems are also compared and is tried to correlate with the crystallite size and presence of dopant metal. |
| URI: | http://dyuthi.cusat.ac.in/purl/2127 |
| Files | Size |
|---|---|
| Photodegradation of methylorange...pdf | (127.3Kb) |
| Abstract: | Lanthana modified sol-gel titania is prepared through particulate sol-gel route and the physico-chemical characterizations of the prepared systems were done using X-Ray diffration, EDX, BET surface area-pore volume measurements and TG-DTG analysis. Benzophenone was observed to be the sole product in the TiO2 photocatalyzed oxidation of benzhydrol in oxygen purged acetonitrile. The influence of various parameters, like irradiation time, amount of catalyst, concentration of the catalyst and other factors on the photocatalytic oxidation has been investigated. The proposed mechanism envisages the involvement of a superoxide radical anion. |
| URI: | http://dyuthi.cusat.ac.in/purl/2258 |
| Files | Size |
|---|---|
| Dyuthi-SS50.pdf | (293.0Kb) |
Dyuthi Digital Repository Copyright © 2007-2011 Cochin University of Science and Technology. Items in Dyuthi are protected by copyright, with all rights reserved, unless otherwise indicated.