| Abstract: | The objectives of the proposed work are preparation of ceramic nickel zinc ferrite belonging to the series Ni1-XZnXFe2O4 with x varying from 0 to 1in steps of 0.2, structrural, magnetic and electrical characterization of Ni1-XZnXFe2O4, preparation and evaluation of Cure characteristics of Rubber Ferrite Composites (RFCs), magnetic characterization of RFCs using vibrating sample magnetometer (VSM), electrical characterization of RFCs and estimation of magnetostriction constant form HL parameters. The study deals with the structural and magnetic properties of ceramic fillers, variation of coercivity with composition and the variation of magnetization for different filler loadings are compared and correlated. The dielectric properties of ceramic Ni1-XZnXFe2O4 and rubber ferrite composites containing Ni1-XZnXFe2O4 were evaluated and the ac electrical conductivity (ac) of ceramic as well as composite samples can be calculated by using a simple relationship of the form ac = 2f tan 0r, with the data available from dielectric measurements. The results suggest that the ac electrical conductivity is directly proportional to the frequency |
| URI: | http://dyuthi.cusat.ac.in/purl/1001 |
| Files | Size |
|---|---|
| Dyuthi-T0206.pdf | (4.767Mb) |
| Abstract: | Present work deals with the Preparation and characterization of high-k aluminum oxide thin films by atomic layer deposition for gate dielectric applications.The ever-increasing demand for functionality and speed for semiconductor applications requires enhanced performance, which is achieved by the continuous miniaturization of CMOS dimensions. Because of this miniaturization, several parameters, such as the dielectric thickness, come within reach of their physical limit. As the required oxide thickness approaches the sub- l nm range, SiO 2 become unsuitable as a gate dielectric because its limited physical thickness results in excessive leakage current through the gate stack, affecting the long-term reliability of the device. This leakage issue is solved in the 45 mn technology node by the integration of high-k based gate dielectrics, as their higher k-value allows a physically thicker layer while targeting the same capacitance and Equivalent Oxide Thickness (EOT). Moreover, Intel announced that Atomic Layer Deposition (ALD) would be applied to grow these materials on the Si substrate. ALD is based on the sequential use of self-limiting surface reactions of a metallic and oxidizing precursor. This self-limiting feature allows control of material growth and properties at the atomic level, which makes ALD well-suited for the deposition of highly uniform and conformal layers in CMOS devices, even if these have challenging 3D topologies with high aspect-ratios. ALD has currently acquired the status of state-of-the-art and most preferred deposition technique, for producing nano layers of various materials of technological importance. This technique can be adapted to different situations where precision in thickness and perfection in structures are required, especially in the microelectronic scenario. |
| Description: | Department of Instrumentation, Cochin University of Science and Technology |
| URI: | http://dyuthi.cusat.ac.in/purl/3034 |
| Files | Size |
|---|---|
| Dyuthi-T1008.pdf | (7.059Mb) |
| Description: | Department of Physics, Cochin University of Science and Technology |
| URI: | http://dyuthi.cusat.ac.in/purl/2328 |
| Files | Size |
|---|---|
| Dyuthi-T0602.pdf | (22.61Mb) |
| Abstract: | Use of short fibers as reinforcing fillers in rubber composites is on an increasing trend. They are popular due to the possibility of obtaining anisotropic properties, ease of processing and economy. In the preparation of these composites short fibers are incorporated on two roll mixing mills or in internal mixers. This is a high energy intensive time consuming process. This calls for developing less energy intensive and less time consuming processes for incorporation and distribution of short fibers in the rubber matrix. One method for this is to incorporate fibers in the latex stage. The present study is primarily to optimize the preparation of short fiber- natural rubber composite by latex stage compounding and to evaluate the resulting composites in terms of mechanical, dynamic mechanical and thermal properties. A synthetic fiber (Nylon) and a natural fiber (Coir) are used to evaluate the advantages of the processing through latex stage. To extract the full reinforcing potential of the coir fibers the macro fibers are converted to micro fibers through chemical and mechanical means. The thesis is presented in 7 chapters |
| Description: | Department of Polymer Science and Rubber Technology, Cochin University of Science and Technology |
| URI: | http://dyuthi.cusat.ac.in/purl/3680 |
| Files | Size |
|---|---|
| Dyuthi-T1646.pdf | (7.242Mb) |
| Abstract: | Nanophotonics can be regarded as a fusion of nanotechnology and photonics and it is an emerging field providing researchers opportunities in fundamental science and new technologies. In recent times many new methodsand techniques have been developed to prepare materials at nanoscale dimensions. Most of these materials exhibit unique and interesting optical properties and behavior. Many of these have been found to be very useful to develop new devices and systems such as tracers in biological systems, optical limiters, light emitters and energy harvesters. This thesis presents a summary of the work done by the author in the field by choosing a few semiconductor systems to prepare nanomaterials and nanocomposites. Results of the study of linear and nonlinear optical properties of materials thus synthesized are also presented in the various chapters of this thesis. CdS is the material chosen here and the methods and the studies of the detailed investigation are presented in this thesis related to the optical properties of CdS nanoparticles and its composites. Preparation and characterization methods and experimental techniques adopted for the investigations were illustrated in chapter 2 of this thesis. Chapter 3 discusses the preparation of CdS, TiO2 and Au nanoparticles. We observed that the fluorescence behaviour of the CdS nanoparticles, prepared by precipitation technique, depends on excitation wavelength. It was found that the peak emission wavelength can be shifted by as much as 147nm by varyingthe excitation wavelengths and the reason for this phenomenon is the selective excitation of the surface states in the nanoparticles. This provided certain amount of tunability for the emission which results from surface states.TiO2 nanoparticle colloids were prepared by hydrothermal method. The optical absorption study showed a blue shift of absorption edge, indicating quantum confinement effect. The large spectral range investigated allows observing simultaneously direct and indirect band gap optical recombination. The emission studies carried out show four peaks, which are found to be generated from excitonic as well as surface state transitions. It was found that the emission wavelengths of these colloidal nanoparticles and annealed nanoparticles showed two category of surface state emission in addition to the excitonic emission. Au nanoparticles prepared by Turkevich method showed nanoparticles of size below 5nm using plasmonic absorption calculation. It was also found that there was almost no variation in size as the concentration of precursor was changed from 0.2mM to 0.4mM.We have observed SHG from CdS nanostructured thin film prepared onglass substrate by chemical bath deposition technique. The results point out that studied sample has in-plane isotropy. The relative values of tensor components of the second-order susceptibility were determined to be 1, zzz 0.14, xxz and 0.07. zxx These values suggest that the nanocrystals are oriented along the normal direction. However, the origin of such orientation remains unknown at present. Thus CdS is a promising nonlinear optical material for photonic applications, particularly for integrated photonic devices. CdS Au nanocomposite particles were prepared by mixing CdS nanoparticles with Au colloidal nanoparticles. Optical absorption study of these nanoparticles in PVA solution suggests that absorption tail was red shifted compared to CdS nanoparticles. TEM and EDS analysis suggested that the amount of Au nanoparticles present on CdS nanoparticles is very small. Fluorescence emission is unaffected indicating the presence of low level of Au nanoparticles. CdS:Au PVA and CdS PVA nanocomposite films were fabricated and optically characterized. The results showed a red-shift for CdS:Au PVA film for absorption tail compared to CdS PVA film. Nonlinear optical analysis showed a huge nonlinear optical absorption for CdS:Au PVA nanocomposite and CdS:PVA films. Also an enhancement in nonlinear optical absorption is found for CdS:Au PVA thin film compared to the CdS PVA thin film. This enhancement is due to the combined effect of plasmonic as well as excitonic contribution at high input intensity. Samples of CdS doped with TiO2 were also prepared and the linear optical absorption spectra of these nanocompositeparticles clearly indicated the influence of TiO2 nanoparticles. TEM and EDS studies have confirmed the presence of TiO2 on CdS nanoparticles. Fluorescence studies showed that there is an increase in emission peak around 532nm for CdS nanoparticles. Nonlinear optical analysis of CdS:TiO2 PVA nanocomposite films indicated a large nonlinear optical absorption compared to that of CdS:PVA nanocomposite film. The values of nonlinear optical absorption suggests that these nanocomposite particles can be employed for optical limiting applications. CdSe-CdS and CdSe-ZnS core-shell QDs with varying shell size were characterized using UV–VIS spectroscopy. Optical absorption and TEM analysis of these QDs suggested a particle size around 5 nm. It is clearly shown that the surface coating influences the optical properties of QDs in terms of their size. Fluorescence studies reveal the presence of trap states in CdSe-CdS and CdSe- ZnS QDs. Trap states showed an increase as a shell for CdS is introduced and increasing the shell size of CdS beyond a certain value leads to a decrease in the trap state emission. There is no sizeable nonlinear optical absorption observed. In the case of CdSe- ZnS QDs, the trap state emission gets enhanced with the increase in ZnS shell thickness. The enhancement of emission from trap states transition due to the increase in thickness of ZnS shell gives a clear indication of distortion occurring in the spherical symmetry of CdSe quantum dots. Consequently the nonlinear optical absorption of CdSe-ZnS QDs gets increased and the optical limiting threshold is decreased as the shell thickness is increased in respect of CdSe QDs. In comparison with CdSe-CdS QDs, CdSe-ZnS QDs possess much better optical properties and thereby CdSe-ZnS is a strong candidate for nonlinear as well as linear optical applications. |
| Description: | International School of Photonics |
| URI: | http://dyuthi.cusat.ac.in/purl/5028 |
| Files | Size |
|---|---|
| Dyuthi-T2094.pdf | (25.98Mb) |
| Abstract: | The present study on the preparation , characterization and microwave dielectric properties of AnBn-1O3n (N=5,6,8) type perovskite compounds. The explored ceramics show dielectric constant between 11 and 54,quality factor in the range 2400 to 88900 GHz and Tf in the range -73 to +231ppm/0C.Most of the investigated cation deficient hexagonal perovskites show intermediate dielectric constant with high quality factors. This study gives a general introduction about material, scientific and technological aspects of DRs.Three important ,€r ,Q and Tf, used for the DR characterization are described. The relationship of the above parameters with the fundamental material characteristics is discussed. Different modes are excited when a DR is excited with suitable microwave spectrum of frequencies .A description of analytical determination of frequencies and construction of mode charts used for sample design and mode identification are also discussed. In this study several ceramics are developed for DR purposes, very little attention has been paid to grow the single crystals. It might be due to the fact that the difficulties and time involved in the growth of single crystals, big enough to function as microwave resonators make them expensive .However single crystals of these materials may have very high Q values. It is also possible that a better understanding of the dielectric properties in relation to the structure can be arrived using single crystals. Hence one of the future directions of dielectric resonator research should be to grow good quality single crystals of the above materials. |
| URI: | http://dyuthi.cusat.ac.in/purl/25 |
| Files | Size |
|---|---|
| Dyuthi-T0182.pdf | (5.596Mb) |
| Abstract: | Natural rubber latex, an aqueous colloidal dispersion of polyisoprene is widely used in production of gloves, catherers, rubber bands etc. The natural rubber latex content present in products such as gloves causes allergic problems. Of the different types of allergies reported, latex is known to produce Type I and Type IV allergies. Type I is called immediate hypersensitivity and type IV is called delayed hypersensitivity. It has been reported that some of the proteins present in the latex are mainly responsible for the allergic reactions type I. Significant reduction in the allergic response (type I) of natural rubber latex can be achieved by the reduction in its protein content, however out of the total proteins present in the latex or latex film only a fraction is extractable. The major techniques employed to reduce protein content of latex include leaching, autoclaving, chlorination, use of proteolytic enzymes and use of non ionic surfactants. Sulphur vulcanization of dipped products is responsible for Type IV allergy. N-nitrosamine, a carcinogenic substance is produced as a result of sulphur vulcanization. Radiation vulcanization can be used as an alternative for sulphur vulcanization. The current research deals with techniques to reduce the allergy associated with latex products. To reduce the type I allergy, low protein latex is developed using polyethylene glycol, a non- ionic surfactant. The present study employs radiation vulcanization to eliminate type IV allergy. The effect of different cure systems and fillers on the properties of low protein latex is also investigated as a part of the study. |
| URI: | http://dyuthi.cusat.ac.in/purl/5091 |
| Files | Size |
|---|---|
| Dyuthi-T2157.pdf.pdf | (8.640Mb) |
| Abstract: | In this work. Sub-micrometre thick CulnSe2 films were prepared using different techniques viz, selenization through chemically deposited Selenium and Sequential Elemental Evaporation. These methods are simpler than co-evaporation technique, which is known to be the most suitable one for CulnSe2 preparation. The films were optimized by varying the composition over a wide range to find optimum properties for device fabrication. Typical absorber layer thickness of today's solar cell ranges from 2-3m. Thinning of the absorber layer is one of the challenges to reduce the processing time and material usage, particularly of Indium. Here we made an attempt to fabricate solar cell with absorber layer of thickness <lmum. Here In2S3 was used as the buffer layer, replacing toxic CdS. |
| Description: | Department of Physics, Cochin University of Science and Technology |
| URI: | http://dyuthi.cusat.ac.in/purl/2515 |
| Files | Size |
|---|---|
| Dyuthi-T0674.pdf | (9.891Mb) |
| Abstract: | Petroleum, a mixture of organic compounds, comes from underground rock formations ranging in age from ten to several hundred million years. The process by which it is formed and developed is not yet completely known. Studies indicate that petroleum is formed mainly from microscopic-sized marine animals and plants. When these organisms died in water of low oxygen content, they did not decompose. Thus their remains sank to the bottom to be buried under accumulations of sediment. Their conversion to petroleum remains a subject of research even today. |
| Description: | Department of Polymer Science and Rubber Technology, Cochin University of Science and Technology |
| URI: | http://dyuthi.cusat.ac.in/purl/3480 |
| Files | Size |
|---|---|
| Dyuthi-T1446.pdf | (1.988Mb) |
| Abstract: | Coral Reefs are marine, biogenic, wave resistant carbonate structures, formed of the skeletal remains of hermatypic, or reef building organisms. The main reef builders are calcifying Rhodophytes, molluscs, sponges, polychaetes and Cnidarians. Among them, scleractinian corals and hydrocorallians are by far the most important contributors to the formation of reefs. Coral reefs cover approximately 600 thousand square kilometers of the earth's surface (Crossland fl a_1., 1991) which is about 2x106 square kilometres of tropical oceans. |
| Description: | Central Marine Fisheries Research Institute |
| URI: | http://dyuthi.cusat.ac.in/purl/3494 |
| Files | Size |
|---|---|
| Dyuthi-T1451.pdf | (8.309Mb) |
| URI: | http://dyuthi.cusat.ac.in/purl/2190 |
| Files | Size |
|---|---|
| Dyuthi-T0548.pdf | (4.041Mb) |
| Abstract: | This study analyses the role of the Press Council as a champion and guard of free speech. It discusses the extent to which the Council succeeded in achieving its statutory objective of preserving the freedom of the press and maintaining and improving the standards of newspapers and news agencies. It also examines the inherent and in-built weaknesses of the Council and suggests ways and means for restructuring and enlarging its functions. |
| URI: | http://dyuthi.cusat.ac.in/purl/1572 |
| Files | Size |
|---|---|
| Dyuthi-T0229.pdf | (10.73Mb) |
| URI: | http://dyuthi.cusat.ac.in/purl/5287 |
| Files | Size |
|---|---|
| Dyuthi T-2323.pdf | (8.602Mb) |
| URI: | http://dyuthi.cusat.ac.in/purl/1332 |
| Files | Size |
|---|---|
| Mathew George 1987.PDF | (815.5Kb) |
| Abstract: | The present study is on the nature, problems and prospects of the handloom industry in Kerala. The problems of the industry are mostly in the nature of low earnings of the workers, underutilisation of the existing capacity and low profit in its various sectors. The majority of the handloom co-operative societies are either dormant or facing liquidation. The income and employment of weavers are so pitiably low that they are living in utter poverty and starvation. Frequent price fluctuations of yarns, dyes and chemicals increase the cost of production and reduce the profitability. Consequently handloom fabrics are not able to compete with mill cloths and powerloom products. Accumulating the unsold stocks in the godowns of co-operative societies and with master weavers has become the practice of the day. Spinning mills in Kerala are producing only lower counts of yarns. S, handloom industry has to depend on textile mills in Tamil Nadu for higher counts of yarn. They create artificial scarcity and increase the prices exflorbitantly. Wage rates prevailing in Kerala are higher than those in Tamil Hadu. So rich master weavers are migrating to Tamil.Nadu and exporting the fabrics. under the label 'Kera1a Handlooms'. Governmental efforts to tackle the crisis by way of rebates and subsidies are found to be futile. |
| Description: | Department of applied economics, Cochin University of Science And Technology |
| URI: | http://dyuthi.cusat.ac.in/purl/3340 |
| Files | Size |
|---|---|
| Dyuthi-T1302.pdf | (5.430Mb) |
| Abstract: | The thesis is the outcome of the exhaustive theoretical and experimental investigations performed on Printed Monopole Antennas loaded with different geometries .The work presented in this thesis describes the development of a 3D- FDTD(Finite Difference Time Domain) Modeller using MATLAB for the numerical computation of the radiation characteristics of the antenna. The predicted results are verified experimentally and also through simulation using Ansoft HFSS.The effect of top loading of the monopole with different geometries ,the dimensions of the loading patch and ground plane and the material parameters of the dielectric substrate upon the radiation performance of the antenna is studied in detail. Optimized Printed Monopole antennas suitable for Ultra Wide Band (UWB) applications have been developed. |
| Description: | Department of Electronics, Cochin University of Science and Technology |
| URI: | http://dyuthi.cusat.ac.in/purl/2692 |
| Files | Size |
|---|---|
| Dyuthi-T0744.pdf | (12.77Mb) |
| Abstract: | The study is confined to non-mechanised private and cooperative granite quarries in Thrissur district. There are 90 non -mechanised quarries in Thrissur district. Data were collected for the period from 1994-'95 to 1999-2000. 315* March of every year was considered as the closing date of the year. It envisages an analysis of various problems connected with quarrying operations, financial analysis, cost analysis, demand and supply position of quarry products and socio-economic background of workers. It also suggest some measures to improve the working conditions of granite quarrying. |
| Description: | School of Management Studies, Cochin University of Science & Technology |
| URI: | http://dyuthi.cusat.ac.in/purl/3490 |
| Files | Size |
|---|---|
| Dyuthi-T1449.pdf | (2.645Mb) |
| URI: | http://dyuthi.cusat.ac.in/purl/1033 |
| Files | Size |
|---|---|
| Jacob M J 1988.pdf | (185.5Kb) |
| Abstract: | In this thesis we attempt to make a probabilistic analysis of some physically realizable, though complex, storage and queueing models. It is essentially a mathematical study of the stochastic processes underlying these models. Our aim is to have an improved understanding of the behaviour of such models, that may widen their applicability. Different inventory systems with randon1 lead times, vacation to the server, bulk demands, varying ordering levels, etc. are considered. Also we study some finite and infinite capacity queueing systems with bulk service and vacation to the server and obtain the transient solution in certain cases. Each chapter in the thesis is provided with self introduction and some important references |
| Description: | Department of Mathematics and Statistics Cochin University of Science and Technology |
| URI: | http://dyuthi.cusat.ac.in/purl/3582 |
| Files | Size |
|---|---|
| Dyuthi-T1554.pdf | (3.014Mb) |
Dyuthi Digital Repository Copyright © 2007-2011 Cochin University of Science and Technology. Items in Dyuthi are protected by copyright, with all rights reserved, unless otherwise indicated.