| Abstract: | Reduction of radar cross -section of dihedral corner reflectors using simulated corrugated surface (SCS) is reported. The technique is found to be more effective in the reduction of RCS or corner reflectors for normal incidence . A typical reduction of 40-50 dB is achieved using this method. |
| URI: | http://dyuthi.cusat.ac.in/jspui/handle/dyuthi/1575 |
| Files | Size |
|---|---|
| Backscattering ... rs using SCS technique.PDF | (1.362Mb) |
| Abstract: | One thousand, two hundred and sixty four samples of individually quick-frozen (IQF) peeled and deveined raw and 914 samples of cooked ready to eat shrimp samples produced from farm raised black tiger (Penaeus monodon) obtained from a seafood unit working under HACCP concept were analysed for total aerobic plate count (APC), coliform count, Escherichia coli, coagulase positive Staphylococci and Salmonella. The overall bacteriological quality of the product was found to be good. Of the frozen raw shrimp, 96% of samples showed APC below 105 while 99% of the frozen cooked ready-to-eat samples showed APC less than 104. The APC ranged from 1·0´102 to 4·2´106 cfu/gm in frozen raw shrimp and from 1·0´102 to 6·4´104 cfu/gm in the frozen cooked shrimp. Prevalences of coliforms in raw shrimp and cooked shrimp samples were 14·4% and 2·9% respectively. The coliform count in raw products ranged from 1·0´101 to 2·5´103 cfu/gm and in the cooked products, from 1·0 ´101 to 1·8´102 cfu/gm. Although all the cooked shrimp samples were free of coagulase positive staphylococci, E. coli and Salmonella, 1·0, 2·0 and 0·1% of the frozen raw shrimp samples tested positive for coagulase positive Staphylococci, E. coli and Salmonella respectively. The Salmonella strain was identified as Salmonella typhimurium. The results of the present study highlight the importance of implementation of HACCP system in the seafood industry to ensure consistent quality of frozen seafood |
| Description: | Food Microbiology, 1998, 15, 177–183 |
| URI: | http://dyuthi.cusat.ac.in/purl/3959 |
| Files | Size |
|---|---|
| Bacteriological ... rimp (Penaeus monodon).pdf | (74.59Kb) |
| Abstract: | Bacillus subtilis CBTK 106, isolated from banana wastes, produced high titres of a-amylase when banana fruit stalk was used as substrate in a solid-state fermentation system. The e¤ects of initial moisture content, particle size, cooking time and temperature, pH, incubation temperature, additional nutrients, inoculum size and incubation period on the production of a- amylase were characterised. A maximum yield of 5 345 000 U mg~1 min~1 was recorded when pretreated banana fruit stalk (autoclaved at 121 ¡C for 60 min) was used as substrate with 70% initial moisture content, 400 lm particle size, an initial pH of 7.0, a temperature of 35 ¡C, and additional nutrients (ammonium sulphate/sodium nitrate at 1.0%, beef extract/peptone at 0.5%, glucose/sucrose/starch/maltose at 0.1% and potassium chloride/sodium chloride at 1.0%) in the medium, with an inoculum-to-substrate ratio of 10% (v/w) for 24 h. The enzyme yield was 2.65-fold higher with banana fruit stalk medium compared to wheat bran |
| Description: | Appl Microbiol Biotechnol (1996) 46:106-111 |
| URI: | http://dyuthi.cusat.ac.in/purl/4238 |
| Files | Size |
|---|---|
| Banana waste as ... lid-state fermentation.pdf | (216.5Kb) |
| Abstract: | Worldwide, Micro, Small and Medium Enterprises (MSMEs) have been accepted as an engine of economic growth and for promoting equitable development. In developing countries including India, Micro, Small and Medium Enterprises sector constitute an important part in its development. In spite of this importance, this sector face number of constraints like absence of adequate and timely supply of bank finance, difficulties in procuring raw materials, marketing and distribution challenges and non availability of suitable technology. Review of literature found that there exists problem in accessing finance from banks and financial institutions and this problem may differ from region to region, between sectors, or between individual enterprises within a sector. This paper tries to identify the various barriers faced by these units in raising finance and also try to identify the various sources of finance other than banks. The study is based upon the primary data collected from the 200 MSMEs owners in Kozhikode District of Kerala. The data has been analysed with the help of percentage. The study attempts to submit some recommendations to enhance the overall credit accessibility to MSMEs sector |
| Description: | Abhinav National Monthly Refereed Journal of Research in Commerce & Management,Volume 3, Issue 5 (May, 2014) |
| URI: | http://dyuthi.cusat.ac.in/purl/4661 |
| Files | Size |
|---|---|
| Barriers Faced ... ses In Raising Finance.pdf | (307.2Kb) |
| Abstract: | This paper aims to highlight the difficulties faced by organizations in implementing Total Productive Maintenance (TPM). The authors with their experience in TPM and the refinery industry have attempted to understand the factors that hinder implementation of TPM. The paper first explains in brief the concepts of TPM and why TPM is a must for organizations in this complex dynamic business environment. It then takes up the various issues that hamper implementation of TPM in industries. Solutions to overcome the barriers are discussed briefly but will be taken up in detail in another paper with specific reference to refinery scenario |
| Description: | INTERNATIONAL JOURNAL OF SCIENTIFIC & TECHNOLOGY RESEARCH VOLUME 2, ISSUE 5, MAY 2013 |
| URI: | http://dyuthi.cusat.ac.in/purl/4503 |
| Files | Size |
|---|---|
| Barriers In TPM Implementation In Industries.pdf | (355.2Kb) |
| Abstract: | The electron donating properties of La2O3 activated at 300, 500 and 800·C and its mixed oxides with alumina are reported from the studies on adsorption of electron acceptors of varying electron affinity on La203. The electron acceptors with their electron affinity values given in parenthesis are: 7,7,8,8-tetracyanoquinodimethane (2.84 eV), 2,3,5,6-tetrachloro-I,4-benzoquinone (2.40 eV) and p-dinitrobenzene(l.77eV). The basicity of the oxide has been determined by titration with n-butylamine and Ho.max values are reported. The limit of electron transfer from the oxide to the electron acceptor is between 2.40 and 1.77 eV. It is observed that La203 promotes the surface electron properties of alumina without changing its limit of electron transfer. |
| URI: | http://dyuthi.cusat.ac.in/purl/2217 |
| Files | Size |
|---|---|
| Dyuthi-SS22.pdf | (236.1Kb) |
| Abstract: | This deals a basic idea about basics of research, it helps the beginners how to proceed research activities |
| URI: | http://dyuthi.cusat.ac.in/purl/4913 |
| Files | Size |
|---|---|
| Basics of Scientific Research Mohankumar.pptx | (745.2Kb) |
| Abstract: | A new microwave dielectric resonator Ba(Tb1/2Nb1/2)03 has been prepared and characterized in the microwave frequency region. 1 wt% CeO2 is used as additive to reduce the sintering temperature. The sintered samples were characterized by XRD, SEM and Raman spectroscopic methods. Microwave DR properties such as er, Q factor and temperature-coefficient of resonant frequency (Ti) have been measured using a HP 8510 B Network Analyzer. Cylindrical DRs of Ba(Tb1/2Nbi/2)03 showed high Er (~ 37), high Q (~3,200) and low Tf (~10 ppm /°C) at 4 GHz and hence are useful for practical applications |
| URI: | http://dyuthi.cusat.ac.in/purl/1447 |
| Files | Size |
|---|---|
| Ba(Tb1 2Nb1 2)0 ... e dielectric resonator.PDF | (2.173Mb) |
| URI: | http://dyuthi.cusat.ac.in/purl/4916 |
| Files | Size |
|---|---|
| Bayesian Analys ... ss Model- Ayon Ganguly.pdf | (930.1Kb) |
| Abstract: | This thesis Entitled Bayesian inference in Exponential and pareto populations in the presence of outliers. The main theme of the present thesis is focussed on various estimation problems using the Bayesian appraoch, falling under the general category of accommodation procedures for analysing Pareto data containing outlier. In Chapter II. the problem of estimation of parameters in the classical Pareto distribution specified by the density function. In Chapter IV. we discuss the estimation of (1.19) when the sample contain a known number of outliers under three different data generating mechanisms, viz. the exchangeable model. Chapter V the prediction of a future observation based on a random sample that contains one contaminant. Chapter VI is devoted to the study of estimation problems concerning the exponential parameters under a k-outlier model. |
| Description: | Department of Mathematics and Statistics, Cochin University of Science and Technoloy |
| URI: | http://dyuthi.cusat.ac.in/purl/3066 |
| Files | Size |
|---|---|
| Dyuthi-T1040.pdf | (4.788Mb) |
| URI: | http://dyuthi.cusat.ac.in/purl/1851 |
| Files | Size |
|---|---|
| Dyuthi-T0059.pdf | (4.162Mb) |
| Abstract: | ACCURATE sensing of vehicle position and attitude is still a very challenging problem in many mobile robot applications. The mobile robot vehicle applications must have some means of estimating where they are and in which direction they are heading. Many existing indoor positioning systems are limited in workspace and robustness because they require clear lines-of-sight or do not provide absolute, driftfree measurements.The research work presented in this dissertation provides a new approach to position and attitude sensing system designed specifically to meet the challenges of operation in a realistic, cluttered indoor environment, such as that of an office building, hospital, industrial or warehouse. This is accomplished by an innovative assembly of infrared LED source that restricts the spreading of the light intensity distribution confined to a sheet of light and is encoded with localization and traffic information. This Digital Infrared Sheet of Light Beacon (DISLiB) developed for mobile robot is a high resolution absolute localization system which is simple, fast, accurate and robust, without much of computational burden or significant processing. Most of the available beacon's performance in corridors and narrow passages are not satisfactory, whereas the performance of DISLiB is very encouraging in such situations. This research overcomes most of the inherent limitations of existing systems.The work further examines the odometric localization errors caused by over count readings of an optical encoder based odometric system in a mobile robot due to wheel-slippage and terrain irregularities. A simple and efficient method is investigated and realized using an FPGA for reducing the errors. The detection and correction is based on redundant encoder measurements. The method suggested relies on the fact that the wheel slippage or terrain irregularities cause more count readings from the encoder than what corresponds to the actual distance travelled by the vehicle.The application of encoded Digital Infrared Sheet of Light Beacon (DISLiB) system can be extended to intelligent control of the public transportation system. The system is capable of receiving traffic status input through a GSM (Global System Mobile) modem. The vehicles have infrared receivers and processors capable of decoding the information, and generating the audio and video messages to assist the driver. The thesis further examines the usefulness of the technique to assist the movement of differently-able (blind) persons in indoor or outdoor premises of his residence.The work addressed in this thesis suggests a new way forward in the development of autonomous robotics and guidance systems. However, this work can be easily extended to many other challenging domains, as well. |
| Description: | Department of Electronics, Cochin University of Science and Technology |
| URI: | http://dyuthi.cusat.ac.in/purl/2483 |
| Files | Size |
|---|---|
| Dyuthi-T0666.pdf | (13.00Mb) |
| Abstract: | In the present thesis, possibility of beam shaping of sectoral horns and corner reflector systems'has been studied in detail. The experimental results obtained in the above two cases are compared. As far as the flanged sectoral horns are concerned, the special advantage is that the gain is increased without impairing impedance conditions. An intense study on corner reflector antennas shows that the been broadening or focussing will be possible by adjusting parameters involved. Beam tilting by imposing asymmetries is another interesting property of the systems. A comprehensive study of these fields has been presented in Chapter II. Chapter III is exclusively for describing the experimental techniques used in the present investigation. In Chapter IV, experimental results on flanged sectoral horns and corner reflector eyetses are presented. A comparative analysis of the experimental results obtained with flanged sectoral horns and corner reflector systems is presented in the Chapter V. The similarity and close resemblance in each aspects are shown by presenting typical results from these two eysteee. Theoretical aspects of both types of antennas are considered in Chapter VI. Attempts are made for co-ordinating the theoretical aspects and drawing a final conclusion. In Chapter VII. the final conclusion that the flanged sectoral horn may be considered as a corner reflector system has been drawn. The importance of the conclusions and usefulness are pointed out. The scope for further work in these lines has been indicated. |
| Description: | Department of physics, Cochin University of Science And Technology |
| URI: | http://dyuthi.cusat.ac.in/purl/3291 |
| Files | Size |
|---|---|
| Dyuthi-T1273.pdf | (7.116Mb) |
| Abstract: | In this paper, a novel application of solid acid catalysts in the Beckmann rearrangement of E,E-cinnamaldoxime in the synthesis of an important heterocyclic compound; isoquinoline is reported. E,E-Cinnamaldoxime under ambient reaction conditions on zeolite catalysts underwent Beckmann rearrangement to produce isoquinoline in yields of ca. 86–95%. Cinnamonitrile and cinnamaldehyde were formed as by-products. LaH-Y zeolite produces maximum amount of the desired product (yield 95.6%). However, the catalysts are susceptible for deactivation due to the basic nature of the reactants and products, which neutralize the active sites. H-Y zeolite is more susceptible (22% deactivation in 10 h) for deactivation compared to the cerium-exchanged counterpart (18% deactivation in 10 h). Thus, the optimal protocol allows isoquinoline to be synthesised in excellent yields through the Beckmann rearrangement of cinnamaldoxime. The reaction is simple, effective, does not involve any other additives, and environmentally benign. |
| URI: | http://dyuthi.cusat.ac.in/purl/2315 |
| Files | Size |
|---|---|
| Dyuthi-SS83.pdf | (457.2Kb) |
| Abstract: | The research in the area of geopolymer is gaining momentum during the past 20 years. Studies confirm that geopolymer concrete has good compressive strength, tensile strength, flexural strength, modulus of elasticity and durability. These properties are comparable with OPC concrete.There are many occasions where concrete is exposed to elevated temperatures like fire exposure from thermal processor, exposure from furnaces, nuclear exposure, etc.. In such cases, understanding of the behaviour of concrete and structural members exposed to elevated temperatures is vital. Even though many research reports are available about the behaviour of OPC concrete at elevated temperatures, there is limited information available about the behaviour of geopolymer concrete after exposure to elevated temperatures. A preliminary study was carried out for the selection of a mix proportion. The important variable considered in the present study include alkali/fly ash ratio, percentage of total aggregate content, fine aggregate to total aggregate ratio, molarity of sodium hydroxide, sodium silicate to sodium hydroxide ratio, curing temperature and curing period. Influence of different variables on engineering properties of geopolymer concrete was investigated. The study on interface shear strength of reinforced and unreinforced geopolymer concrete as well as OPC concrete was also carried out. Engineering properties of fly ash based geopolymer concrete after exposure to elevated temperatures (ambient to 800 °C) were studied and the corresponding results were compared with those of conventional concrete. Scanning Electron Microscope analysis, Fourier Transform Infrared analysis, X-ray powder Diffractometer analysis and Thermogravimetric analysis of geopolymer mortar or paste at ambient temperature and after exposure to elevated temperature were also carried out in the present research work. Experimental study was conducted on geopolymer concrete beams after exposure to elevated temperatures (ambient to 800 °C). Load deflection characteristics, ductility and moment-curvature behaviour of the geopolymer concrete beams after exposure to elevated temperatures were investigated. Based on the present study, major conclusions derived could be summarized as follows. There is a definite proportion for various ingredients to achieve maximum strength properties. Geopolymer concrete with total aggregate content of 70% by volume, ratio of fine aggregate to total aggregate of 0.35, NaOH molarity 10, Na2SiO3/NaOH ratio of 2.5 and alkali to fly ash ratio of 0.55 gave maximum compressive strength in the present study. An early strength development in geopolymer concrete could be achieved by the proper selection of curing temperature and the period of curing. With 24 hours of curing at 100 °C, 96.4% of the 28th day cube compressive strength could be achieved in 7 days in the present study. The interface shear strength of geopolymer concrete is lower to that of OPC concrete. Compared to OPC concrete, a reduction in the interface shear strength by 33% and 29% was observed for unreinforced and reinforced geopolymer specimens respectively. The interface shear strength of geopolymer concrete is lower than ordinary Portland cement concrete. The interface shear strength of geopolymer concrete can be approximately estimated as 50% of the value obtained based on the available equations for the calculation of interface shear strength of ordinary portland cement concrete (method used in Mattock and ACI). Fly ash based geopolymer concrete undergoes a high rate of strength loss (compressive strength, tensile strength and modulus of elasticity) during its early heating period (up to 200 °C) compared to OPC concrete. At a temperature exposure beyond 600 °C, the unreacted crystalline materials in geopolymer concrete get transformed into amorphous state and undergo polymerization. As a result, there is no further strength loss (compressive strength, tensile strength and modulus of elasticity) in geopolymer concrete, whereas, OPC concrete continues to lose its strength properties at a faster rate beyond a temperature exposure of 600 °C. At present no equation is available to predict the strength properties of geopolymer concrete after exposure to elevated temperatures. Based on the study carried out, new equations have been proposed to predict the residual strengths (cube compressive strength, split tensile strength and modulus of elasticity) of geopolymer concrete after exposure to elevated temperatures (upto 800 °C). These equations could be used for material modelling until better refined equations are available. Compared to OPC concrete, geopolymer concrete shows better resistance against surface cracking when exposed to elevated temperatures. In the present study, while OPC concrete started developing cracks at 400 °C, geopolymer concrete did not show any visible cracks up to 600 °C and developed only minor cracks at an exposure temperatureof 800 °C. Geopolymer concrete beams develop crack at an early load stages if they are exposed to elevated temperatures. Even though the material strength of the geopolymer concrete does not decrease beyond 600 °C, the flexural strength of corresponding beam reduces rapidly after 600 °C temperature exposure, primarily due to the rapid loss of the strength of steel. With increase in temperature, the curvature at yield point of geopolymer concrete beam increases and thereby the ductility reduces. In the present study, compared to the ductility at ambient temperature, the ductility of geopolymer concrete beams reduces by 63.8% at 800 °C temperature exposure. Appropriate equations have been proposed to predict the service load crack width of geopolymer concrete beam exposed to elevated temperatures. These equations could be used to limit the service load on geopolymer concrete beams exposed to elevated temperatures (up to 800 °C) for a predefined crack width (between 0.1mm and 0.3 mm) or vice versa. The moment-curvature relationship of geopolymer concrete beams at ambient temperature is similar to that of RCC beams and this could be predicted using strain compatibility approach Once exposed to an elevated temperature, the strain compatibility approach underestimates the curvature of geopolymer concrete beams between the first cracking and yielding point. |
| Description: | Division of Safety and Fire Engineering |
| URI: | http://dyuthi.cusat.ac.in/purl/5030 |
| Files | Size |
|---|---|
| Dyuthi-T2097.pdf | (5.482Mb) |
| Abstract: | This study aims to analyze, compare and contrast the behavioral competency of officials in commercial banks headquartered in Kerala. This is done by analyzing the soft skills/behavioral skills possessed by an individual employee in both clerical and managerial levels and the means adopted to enhance their said skills in near future. The study was conducted with the objective of analyzing the behavioral competency of the managers and clerical staff in the commercial banks headquartered in Kerala. The researcher has gone through the available literature with respect to employee competency, job satisfaction and employee performance evaluation to formulate the problem and conceptualize the framework of the study. The study concluded that the competency of the employees differs from one bank to the other but strengthening the employees’ competency is the only possible solution by which the banks can determine their future growth prospects. Only through competency, banks can achieve high level of performance especially under the globalised situation. |
| URI: | http://dyuthi.cusat.ac.in/purl/4997 |
| Files | Size |
|---|---|
| Dyuthi-T2066.pdf | (4.464Mb) |
Dyuthi Digital Repository Copyright © 2007-2011 Cochin University of Science and Technology. Items in Dyuthi are protected by copyright, with all rights reserved, unless otherwise indicated.