Abstract: | This research project explores the utilization of cardanol in various capacities for rubber processing. Cardanol is a phenol with a long side chain in the meta position of the benzene ring. It is obtained by the vacuum distillation of cashew Hut shell liquid (CNSL) which is a cheap agro-byproduct. In this study, the plasticizer property of cardanol was investigated in silica filled and HAF black filled NR, NBR, EPDM and CR by comparing cure characteristics and mechanical properties of vulcanizates containing conventional plasticizer with those containing cardanol as plasticizer. The co-activator, antioxidant and accelerator properties were investigated in gum samples of NR, NBR, EPDM and CR by comparing the properties of vulcanizates which contain conventional co-activator, antioxidant and accelerator with those in which each of them was replaced by cardanol. The general effectiveness of cardanol was investigated by determination of cure time , measurement of physical and mechanical properties, ageing studies, crosslink density, extractability, FTIR spectra, TGA etc.The results show that cardanol can be a substitute for aromatic oil in both silica filled and HAF black filled NR. Again, it can replace dioctyl phthalate in both silica filled and HAF black filled NBR. Similarly, cardanol Can replace naphthenic oil in silica filled as well as HAF black filled EPDM and CR. The cure characteristics and mechanical properties are comparable in all the eight cases. The co-activator property of cardanol is comparable to stearic acid in all the four rubbers. The cure characteristics and mechanical properties in this case are also comparable. The antioxidant ,property of cardanol is comparable to TQ in all the four rubbers. The antioxidant property of cardanol is comparable to TQ in all the four case of NBR and EPDM.The accelerator property of cardarlol is comparable with CBS in the case of NBR and EPDM. No accelerator property is observed in the case of NR. The accelerator property of cardanol in CR is not negligible when compared with TMTD. |
Description: | Department of Polymer Science and Rubber Technology, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/2550 |
Files | Size |
---|---|
Dyuthi-T0694.pdf | (10.18Mb) |
Abstract: | This thesis presents the Radar Cross Section measurements of different geometric structures such as flat plate,cylinder, corner reflector and circular cone loaded with fractal based metallo dielectric structures.Use of different fractal geometris,metallizations of different shapes as well as the frequency tanability is investigated for TE and TM polarization of the incident electromagnetic field.Application of fractal based metallo-dielectric structures results in RCS reduction over a wide range of frequency bands.RCS enhancement of dihedral corner is observed at certain acute and obtuse corner angles.The experimental results are validated using electromagnetic simulation softwares. |
Description: | Department of Electronics, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/2700 |
Files | Size |
---|---|
Dyuthi-T0752.pdf | (5.140Mb) |
URI: | http://dyuthi.cusat.ac.in/purl/1708 |
Files | Size |
---|---|
Dyuthi-T0014.pdf | (5.767Mb) |
URI: | http://dyuthi.cusat.ac.in/purl/5292 |
Files | Size |
---|---|
Dyuthi T-2328.pdf | (4.159Mb) |
Abstract: | For years, choosing the right career by monitoring the trends and scope for different career paths have been a requirement for all youngsters all over the world. In this paper we provide a scientific, data mining based method for job absorption rate prediction and predicting the waiting time needed for 100% placement, for different engineering courses in India. This will help the students in India in a great deal in deciding the right discipline for them for a bright future. Information about passed out students are obtained from the NTMIS ( National technical manpower information system ) NODAL center in Kochi, India residing in Cochin University of science and technology |
Description: | International Journal of Recent Trends in Engineering, Vol. 1, No. 1, May 2009 |
URI: | http://dyuthi.cusat.ac.in/purl/4089 |
Files | Size |
---|---|
Applying Data m ... s for Career Selection.pdf | (362.7Kb) |
URI: | http://dyuthi.cusat.ac.in/purl/4986 |
Files | Size |
---|---|
Dyuthi-T2057.pdf | (22.85Mb) |
URI: | http://dyuthi.cusat.ac.in/purl/5256 |
Files | Size |
---|---|
Dyuthi T-2292.pdf | (6.112Mb) |
Abstract: | n the recent years protection of information in digital form is becoming more important. Image and video encryption has applications in various fields including Internet communications, multimedia systems, medical imaging, Tele-medicine and military communications. During storage as well as in transmission, the multimedia information is being exposed to unauthorized entities unless otherwise adequate security measures are built around the information system. There are many kinds of security threats during the transmission of vital classified information through insecure communication channels. Various encryption schemes are available today to deal with information security issues. Data encryption is widely used to protect sensitive data against the security threat in the form of “attack on confidentiality”. Secure transmission of information through insecure communication channels also requires encryption at the sending side and decryption at the receiving side. Encryption of large text message and image takes time before they can be transmitted, causing considerable delay in successive transmission of information in real-time. In order to minimize the latency, efficient encryption algorithms are needed. An encryption procedure with adequate security and high throughput is sought in multimedia encryption applications. Traditional symmetric key block ciphers like Data Encryption Standard (DES), Advanced Encryption Standard (AES) and Escrowed Encryption Standard (EES) are not efficient when the data size is large. With the availability of fast computing tools and communication networks at relatively lower costs today, these encryption standards appear to be not as fast as one would like. High throughput encryption and decryption are becoming increasingly important in the area of high-speed networking. Fast encryption algorithms are needed in these days for high-speed secure communication of multimedia data. It has been shown that public key algorithms are not a substitute for symmetric-key algorithms. Public key algorithms are slow, whereas symmetric key algorithms generally run much faster. Also, public key systems are vulnerable to chosen plaintext attack. In this research work, a fast symmetric key encryption scheme, entitled “Matrix Array Symmetric Key (MASK) encryption” based on matrix and array manipulations has been conceived and developed. Fast conversion has been achieved with the use of matrix table look-up substitution, array based transposition and circular shift operations that are performed in the algorithm. MASK encryption is a new concept in symmetric key cryptography. It employs matrix and array manipulation technique using secret information and data values. It is a block cipher operated on plain text message (or image) blocks of 128 bits using a secret key of size 128 bits producing cipher text message (or cipher image) blocks of the same size. This cipher has two advantages over traditional ciphers. First, the encryption and decryption procedures are much simpler, and consequently, much faster. Second, the key avalanche effect produced in the ciphertext output is better than that of AES. |
Description: | Division of Electronics Engineering, School of Engineering, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/3089 |
Files | Size |
---|---|
Dyuthi-T1063.pdf | (1.722Mb) |
URI: | http://dyuthi.cusat.ac.in/purl/2489 |
Files | Size |
---|---|
Dyuthi-P0276.pdf | (145.7Kb) |
Abstract: | This thesis Entitled Application of Biofloc technology (BFT) In the Nursery Rearing and Farming of Giant Freshwater Prawn,Macrobrachium Rosenbergii(De Man). Aquaculture, rearing plants and animals under controlled conditions is growing with an annual growth rate of 8.3% in the period 1970-2008 (FAO, 2010). This trend of growth is essential for the supply of protein-rich food for ever increasing world population. But growth and development of aquaculture should be in sustainable manner, preferably without jeopardizing the aquatic environment.In the present study, the application of BFT in the nursery rearing and farming ofgiant freshwater prawn, M. rosenbergii, is attempted. The result of the study is organised into eight chapters. In the first chapter, the subject is adequately introduced. Various types of aquaculture practices followed, development and status of Indian aquaculture, present status of freshwater pravm culture, BF T and its use for the sustainable aquaculture systems, theory of BFT based aquaculture practices, hypothesis, objective and outline of the thesis are described. An extensive review of literature on studies carried out so far on biofloc based aquaculture are given in chapter 2. The third chapter deals with the application of BFT in the primary nursery phase of freshwater prawn. Several workers suggested the need for an intermediate nursery phase in the culture system of freshwater prawn for the successful production. Thirty day experiment was conducted to study the effect of BFT on the water quality, and animal welfare under the various stocking densities. The study concluded that stocking finfishes in biofloc-based monoculture system of freshwater prawns has the potential of increasing total yield. Prawns having a higher commercial value than finfishes besides ensuring economic sustainability. Results showed that prawn yield and survival was better in catla dominated tanks. Based on the results of the study, it is recommended to incorporate 25% rohu and 75% catla in the biofloc-based culture system of giant freshwater prawns. The results of the present study also recommend to stock relatively larger catla for biofloc-based culture system. Fish production was also higher in the 100% catla tank. When catla was added in higher percentages it should ensured that the hiding objects in the culture ponds shall be used in order to reduce the chance of cannibalism among prawns. rohu and catla equally have the ability to harvest the biofloc, catla consumes the planktonic contributes in the floc whereas rohu grazed on the bacterial consortium suspended in the water column. In Chapter 8, recommendations and future research perspectives in the field of biofloc based aquaculture is presented. |
Description: | School of Industrial Fisheries, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/3090 |
Files | Size |
---|---|
Dyuthi-T1064.pdf | (9.603Mb) |
Description: | 14th Biennial International Symposium on Antennas and propagation Department of Electronics, Cochin University of Science & Technology, Cochin 682022, INDIA |
URI: | http://dyuthi.cusat.ac.in/purl/4914 |
Files | Size |
---|---|
Proceedings Final APSYM 2014 -final - CD.pdf | (39.18Mb) |
Abstract: | Aquatic ecosystem in the south west coast of India is noted for its diversity of habitats. Very often these environments turn bluegreen when the bloom of bluegreen algae (cyanobacteria) appear consequent to eutrophication. This phenomenon occursin these habitats one after the other or simultaneously. This conspicuousness make one curious enough to know more about these nature’s gift bestowed upon mankind. While persuing the literature on the magnificent flora) it is understood that it may provide food fertilizer, chemicals and bioactive substances. These bioactive substances are likely to be involved in regulating natural populations and are potentially useful as biochemical tools and as herbicidal or biocontrol agents. The role of cyanobacteria in the aquatic food chain and contribution in abatement of heavy metals from the natural environment are well documented. Considering the manifold utilization of the flora and their significance in the food chain, the present investigation has been undertaken |
Description: | Department of Marine Biology, Microbiology and Biochemistry, School of Marine Sciences, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/3397 |
Files | Size |
---|---|
Dyuthi-T1374.pdf | (3.907Mb) |
Abstract: | The present thesis develops from the point of view of titania sol-gel chemistry and an attempt is made to address the modification of the process for better photoactive titania by selective doping and also demonstration of utilization of the process for the preparation of supported membranes and self cleaning films.A general introduction to nanomaterials, nanocrystalline titania and sol-gel chemistry are presented in the first chapter. A brief and updated literature review on sol-gel titania, with special emphasis on catalytic and photocatalytic properties and anatase to rutile transformation are covered. Based on critical assessment of the reported information the present research problem has been defined.The second chapter describes a new aqueous sol-gel method for the preparation of nanocrystalline titania using titanyl sulphate as precursor. This approach is novel since no earlier work has been reported in the same lines proposed here. The sol-gel process has been followed at each step using particle size, zeta potential measurements on the sol and thermal analysis of the resultant gel. The prepared powders were then characterized using X-ray diffraction, FTIR, BET surface area analysis and transmission electron microscopy.The third chapter presents a detailed discussion on the physico-chemical characterization of the aqueous sol-gel derived doped titania. The effect of dopants such as tantalum, gadolinium and ytterbium on the anatase to rutile phase transformation, surface area as well as their influence on photoactivity is also included. The fourth chapter demonstrates application of the aqueous sol-gel method in developing titania coatings on porous alumina substrates for controlling the poresize for use as membrane elements in ultrafiltration. Thin coatings having ~50 nm thickness and transparency of ~90% developed on glass surface were tested successfully for self cleaning applications. |
URI: | http://dyuthi.cusat.ac.in/purl/2925 |
Files | Size |
---|---|
Dyuthi-T0916.pdf | (9.431Mb) |
Abstract: | A study focusing on the identification of return generating factors and to the extent of their influence on share prices the outcome will be a tool for investment analysis in the hands of investors portfolio managers and mutual funds who are mostly concerned with changing share prices. Since the study takes into account the influence of macroeconomic variables on variations in share returns by using the outcome the government can frame out suitable policies on long term basis and that will help in nurturing a healthy economy and resultant stock market. As every company management tries to maximize the wealth of the share holders a clear idea about the return generating variables and their influence will help the management to frame various policies to maximize the wealth of the shareholders. |
Description: | School of Management Studies Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/4042 |
Files | Size |
---|---|
Dyuthi-T1807.pdf | (1.987Mb) |
Abstract: | Newspapers cover a large amount of information everyday on topics of varied interests. To a university, newspapers are essential components of communication as they cover various happenings in a university. These items of information are neither stored properly nor put in retrieval systems for future use. The news and views appeared in newspapers can effectively be organized in a digital library making use of open source software. The CUSAT digital library (http://dspace.cusat.ac.in/dspace/) has organized some news items that appeared in local newspapers about the university under a special community named “CUSAT-News”. This article describes the methods of collecting, selecting, organizing, providing access and preserving news items required by a university using DSpace open source software. |
Description: | IFLA international newspaper conference,2010,25-28 february |
URI: | http://dyuthi.cusat.ac.in/purl/4464 |
Files | Size |
---|---|
Archiving News ... g Open Source Software.pdf | (623.6Kb) |
Abstract: | This paper attempts to develop an improved tool, which would read two dimensional(2D) cardiac MRI images and compute areas and volume of the scar tissue. Here the computation would be done on the cardiac MR images to quantify the extent of damage inflicted by myocardial infarction on the cardiac muscle (myocardium) using Interpolation |
Description: | PROCEEDINGS OF ICETECT 2011 |
URI: | http://dyuthi.cusat.ac.in/purl/4236 |
Files | Size |
---|---|
Area and Volume ... rt using Interpolation.pdf | (2.006Mb) |
Abstract: | This study is concerned with Autoregressive Moving Average (ARMA) models of time series. ARMA models form a subclass of the class of general linear models which represents stationary time series, a phenomenon encountered most often in practice by engineers, scientists and economists. It is always desirable to employ models which use parameters parsimoniously. Parsimony will be achieved by ARMA models because it has only finite number of parameters. Even though the discussion is primarily concerned with stationary time series, later we will take up the case of homogeneous non stationary time series which can be transformed to stationary time series. Time series models, obtained with the help of the present and past data is used for forecasting future values. Physical science as well as social science take benefits of forecasting models. The role of forecasting cuts across all fields of management-—finance, marketing, production, business economics, as also in signal process, communication engineering, chemical processes, electronics etc. This high applicability of time series is the motivation to this study. |
Description: | Department of mathematics, Cochin University of Science And Technology |
URI: | http://dyuthi.cusat.ac.in/purl/3326 |
Files | Size |
---|---|
Dyuthi-T1295.pdf | (5.861Mb) |
Dyuthi Digital Repository Copyright © 2007-2011 Cochin University of Science and Technology. Items in Dyuthi are protected by copyright, with all rights reserved, unless otherwise indicated.