| URI: | http://dyuthi.cusat.ac.in/purl/1329 |
| Files | Size |
|---|---|
| Lizy M A 1989.PDF | (1.056Mb) |
| URI: | http://dyuthi.cusat.ac.in/purl/5550 |
| Files | Size |
|---|---|
| Dyuthi T-2592.pdf | (6.380Mb) |
| Abstract: | Salient pole brushless alternators coupled to IC engines are extensively used as stand-by power supply units for meeting in- dustrial power demands. Design of such generators demands high power to weight ratio, high e ciency and low cost per KVA out- put. Moreover, the performance characteristics of such machines like voltage regulation and short circuit ratio (SCR) are critical when these machines are put into parallel operation and alterna- tors for critical applications like defence and aerospace demand very low harmonic content in the output voltage. While designing such alternators, accurate prediction of machine characteristics, including total harmonic distortion (THD) is essential to mini- mize development cost and time. Total harmonic distortion in the output voltage of alternators should be as low as possible especially when powering very sophis- ticated and critical applications. The output voltage waveform of a practical AC generator is replica of the space distribution of the ux density in the air gap and several factors such as shape of the rotor pole face, core saturation, slotting and style of coil disposition make the realization of a sinusoidal air gap ux wave impossible. These ux harmonics introduce undesirable e ects on the alternator performance like high neutral current due to triplen harmonics, voltage distortion, noise, vibration, excessive heating and also extra losses resulting in poor e ciency, which in turn necessitate de-rating of the machine especially when connected to non-linear loads. As an important control unit of brushless alternator, the excitation system and its dynamic performance has a direct impact on alternator's stability and reliability. The thesis explores design and implementation of an excitation i system utilizing third harmonic ux in the air gap of brushless al- ternators, using an additional auxiliary winding, wound for 1=3rd pole pitch, embedded into the stator slots and electrically iso- lated from the main winding. In the third harmonic excitation system, the combined e ect of two auxiliary windings, one with 2=3rd pitch and another third harmonic winding with 1=3rd pitch, are used to ensure good voltage regulation without an electronic automatic voltage regulator (AVR) and also reduces the total harmonic content in the output voltage, cost e ectively. The design of the third harmonic winding by analytic methods demands accurate calculation of third harmonic ux density in the air gap of the machine. However, precise estimation of the amplitude of third harmonic ux in the air gap of a machine by conventional design procedures is di cult due to complex geome- try of the machine and non-linear characteristics of the magnetic materials. As such, prediction of the eld parameters by conven- tional design methods is unreliable and hence virtual prototyping of the machine is done to enable accurate design of the third har- monic excitation system. In the design and development cycle of electrical machines, it is recognized that the use of analytical and experimental methods followed by expensive and in exible prototyping is time consum- ing and no longer cost e ective. Due to advancements in com- putational capabilities over recent years, nite element method (FEM) based virtual prototyping has become an attractive al- ternative to well established semi-analytical and empirical design methods as well as to the still popular trial and error approach followed by the costly and time consuming prototyping. Hence, by virtually prototyping the alternator using FEM, the important performance characteristics of the machine are predicted. Design of third harmonic excitation system is done with the help of results obtained from virtual prototype of the machine. Third harmonic excitation (THE) system is implemented in a 45 KVA ii experimental machine and experiments are conducted to validate the simulation results. Simulation and experimental results show that by utilizing third harmonic ux in the air gap of the ma- chine for excitation purposes during loaded conditions, triplen harmonic content in the output phase voltage is signi cantly re- duced. The prototype machine with third harmonic excitation system designed and developed based on FEM analysis proved to be economical due to its simplicity and has the added advan- tage of reduced harmonics in the output phase voltage. |
| Description: | School of Engineering |
| URI: | http://dyuthi.cusat.ac.in/purl/5024 |
| Files | Size |
|---|---|
| Dyuthi-2090.pdf | (7.056Mb) |
| Abstract: | Fenneropenaeus indicus could be protected from white spot disease (WSD) caused by white spot syndrome virus (WSSV) using a formalin-inactivated viral preparation (IVP) derived from WSSV-infected shrimp tissue. The lowest test quantity of lyophilized IVP coated onto feed at 0.025 g–1 (dry weight) and administered at a rate of 0.035 g feed g–1 body weight d–1 for 7 consecutive days was sufficient to provide protection from WSD for a short period (10 d after cessation of IVP administration). Shrimp that survived challenges on the 5th and 10th days after cessation of IVP administration survived repeated challenges although they were sometimes positive for the presence of WSSV by a polymerase chain reaction (PCR) assay specific for WSSV. These results suggest that F. indicus can be protected from WSD by simple oral administration of IVP |
| Description: | DISEASES OF AQUATIC ORGANISMS,Vol. 66: 265–270, 2005 |
| URI: | http://dyuthi.cusat.ac.in/purl/4437 |
| Files | Size |
|---|---|
| Fenneropenaeus ... te spot syndrome virus.pdf | (505.3Kb) |
| Abstract: | This work envisages the fermentation of prawn shell waste into a more nutritious product with simpler components for application as a feed ingredient in aquaculture. This product would be a rich source of protein along with chitin, minerals, vitamins and N-acetyl glucosamine. A brief description of the various processing (chemical and bioprocess) methods employed for chitin, chitosan and single sell protein preparations from shell waste. It deals with the isolation of micro flora associated with prawn shell degradation. It describes the methods adopted for fermentation of prawn shell degradation and fermentation of prawn shell waste with the selected highly chitinoclastic strains. The comparison of SSF and SmF for each selected strain in terms of enrichment of protein, lipid and carbohydrate in the fermented product was done. Detailed analysis of product quality is discussed. The feed for mulation and feeding experiment explained in detail. Statistical analysis of various biogrowth parameters was done with Duncan’s multiple range test. Very briefly explains 28 days of feeding experiment. A method for the complete utilization of shell waste explains with the help of experiments. |
| URI: | http://dyuthi.cusat.ac.in/purl/82 |
| Files | Size |
|---|---|
| Dyuthi-T0104.pdf | (5.690Mb) |
| Abstract: | Recently’ recognition cnf immobilization ‘technology for the rapid conversion of several substrates into metabolites and repeated reuse of the biocatalysts have drawn the attention of the fermentation scientists and technologists to try these new technologies for the rapid production of pnxkmt and enhancement of the efficiencies of the systems Hence in the present study rice was selected,as a substrate since it is a rich source of starch, available and cultivated throughout the year almost in all part of our country. Rice although known for its use as a staple food in many forms as rice, idli, dosai etc., has not been used in industry extensively. However, it ii; a potential resource for’ the production of alcohol, high protein food anui for sugar and sugar syrups as it is evidenced by the few reports mentioned in the review of literature. Of the several microorganisms available, Bacillus sp, is a known candidate for the production of amylases. Hence in the present study Bacillus sp, was desired for its known efficiencies in starch conversion |
| Description: | Department of Applied Chemistry, Cochin University of Science and Technology |
| URI: | http://dyuthi.cusat.ac.in/purl/3658 |
| Files | Size |
|---|---|
| Dyuthi-T1578.pdf | (3.142Mb) |
| Abstract: | Ferrofluids belonging to the series, Ni x Fe1-x Fe2O4 and Zn x Fe1-x Fe2O4, were synthesized using cold co-precipitation. Liquid films of these ferrofluids were prepared by encapsulating the ferrofluids in between two optically smooth and ultrasonically cleaned glass plates. Magnetic field induced laser transmission through these ferrofluid films has been investigated. Magnetic field values can be calibrated in terms of output laser power in the low field region in which the variation is linear. This set up can be used as a cheap optical gaussmeter in the low field regime. Using the same set-up, the saturation magnetization of the sample used can also be calculated with a sample that is pre-characterized. Hence both magnetization of the sample, as well as applied magnetic field can be sensed and calculated with a precalibrated sample. |
| URI: | http://dyuthi.cusat.ac.in/purl/2844 |
| Files | Size |
|---|---|
| Dyuthi-P00397.pdf | (176.9Kb) |
| Abstract: | A simple fiber optic concentration sensor based on the coupling of light f rom one fiber to another through a solution is discussed. The operational characteristics of the sensor are illustrated by taking the solutions of potassium permanganate and fast green dye as samples.The extrinsic type sensor described here shows linearity at lower concentrations. |
| URI: | http://dyuthi.cusat.ac.in/purl/2638 |
| Files | Size |
|---|---|
| Dyuthi-P0197.pdf | (2.490Mb) |
| Abstract: | A simple, effective and inexpensive fiber optic sensor for investigating the setting characteristics of various grades of cement is described. A finite length of unsheathed multimode optical fiber laid inside the cement mix, is subjected to stress during the setting process. The microbends created on the fiber due to this stress directly influence the intensity of light propagating through the fiber. Continuous monitoring of such variations in the light output transmitted through the fiber gives a clear measure of the setting characteristics of the cement mix, thus providing a simple and elegant technique of great practical importance in the field of civil engineering. The smart fiber optic sensor described above can be incorporated into a building during the construction process itself so that continuous monitoring of the deterioration process for the entire life time of the building can be carried out. |
| URI: | http://dyuthi.cusat.ac.in/purl/2417 |
| Files | Size |
|---|---|
| Dyuthi-P0261.pdf | (246.9Kb) |
| Abstract: | A novel sensing technique for the in situ monitoring of the rate of pulsed laser deposition (PLD) of metal thin films has been developed. This optical fibre based sensor works on the principle of the evanescent wave penetration of waveguide modes into the uncladded portion of a multimode fibre. The utility of this optical fibre sensor is demonstrated in the case of PLD of silver thin films obtained by a Q-switched Nd:YAG laser which is used to irradiate a silver target at the required conditions for the preparation of thin films. This paper describes the performance and characteristics of the sensor and shows how the device can be used as an effective tool for the monitoring of the deposition rate of silver thin films. The fibre optic sensor is very simple, inexpensive and highly sensitive compared with existing techniques for thin film deposition rate measurements |
| URI: | http://dyuthi.cusat.ac.in/purl/1763 |
| Files | Size |
|---|---|
| A fibre optic e ... ed laser deposition of.pdf | (78.21Kb) |
| Abstract: | A novel sensing technique for the in situ monitoring of the rate of pulsed laser deposition (PLD) of metal thin films has been developed. This optical fibre based sensor works on the principle of the evanescent wave penetration of waveguide modes into the uncladded portion of a multimode fibre. The utility of this optical fibre sensor is demonstrated in the case of PLD of silver thin films obtained by a Q-switched Nd:YAG laser which is used to irradiate a silver target at the required conditions for the preparation of thin films. This paper describes the performance and characteristics of the sensor and shows how the device can be used as an effective tool for the monitoring of the deposition rate of silver thin films. The fibre optic sensor is very simple, inexpensive and highly sensitive compared with existing techniques for thin film deposition rate measurements. |
| URI: | http://dyuthi.cusat.ac.in/purl/1764 |
| Files | Size |
|---|---|
| Dyuthi-P0214.pdf | (78.21Kb) |
| Abstract: | A fibre optic technique for detecting trace amounts of nitrite compounds in water is described. The off-line fibre optic sensor outlined here is based on evanescent field absorption in a test solution formed by the reaction of nitrite compounds in water with suitable chemical reagents. A short unclad portion of a plastic clad silica fibre acts as the sensing region. The experimental results clearly establish the usefulness of the present technique for detecting very low concentrations of the order of 1 ppb (parts per billion) of nitrite compounds with a large dynamic range of 1–1000 ppb. Such a high sensitivity enables the present device to be used for measuring the nitrite content in drinking water. |
| URI: | http://dyuthi.cusat.ac.in/purl/1770 |
| Files | Size |
|---|---|
| A fibre optic e ... race nitrites in water.pdf | (89.12Kb) |
| Abstract: | The design and development of a fibre optic evanescent wave refractometer for the detection of trace amounts of paraffin oil and palm oil in coconut oil is presented. This sensor is based on a side-polished plastic optical fibre. At the sensing region, the cladding and a small portion of the core are removed and the fibre nicely polished. The sensing region is fabricated in such a manner that it sits perfectly within a bent mould. This bending of the sensing region enhances its sensitivity. The oil mixture of different mix ratios is introduced into the sensing region and we observed a sharp decrease in the output intensity. The observed variation in the intensity is found to be linear and the detection limit is 2% (by volume) paraffin oil/palm oil in coconut oil. The resolution of this refractometric sensor is of the order of 10−3. Since coconut oil is consumed in large volumes as edible oil in south India, this fibre optic sensor finds great relevance for the detection of adulterants such as paraffin oil or palm oil which are readily miscible in coconut oil. The advantage of this type of sensor is that it is inexpensive and easy to set up. Another attraction of the side-polished fibre is that only a very small amount of analyte is needed and its response time is only 7 s. |
| URI: | http://dyuthi.cusat.ac.in/purl/1778 |
| Files | Size |
|---|---|
| Fibre optic sensor for the detection of.pdf | (87.10Kb) |
| Abstract: | Many finite elements used in structural analysis possess deficiencies like shear locking, incompressibility locking, poor stress predictions within the element domain, violent stress oscillation, poor convergence etc. An approach that can probably overcome many of these problems would be to consider elements in which the assumed displacement functions satisfy the equations of stress field equilibrium. In this method, the finite element will not only have nodal equilibrium of forces, but also have inner stress field equilibrium. The displacement interpolation functions inside each individual element are truncated polynomial solutions of differential equations. Such elements are likely to give better solutions than the existing elements.In this thesis, a new family of finite elements in which the assumed displacement function satisfies the differential equations of stress field equilibrium is proposed. A general procedure for constructing the displacement functions and use of these functions in the generation of elemental stiffness matrices has been developed. The approach to develop field equilibrium elements is quite general and various elements to analyse different types of structures can be formulated from corresponding stress field equilibrium equations. Using this procedure, a nine node quadrilateral element SFCNQ for plane stress analysis, a sixteen node solid element SFCSS for three dimensional stress analysis and a four node quadrilateral element SFCFP for plate bending problems have been formulated.For implementing these elements, computer programs based on modular concepts have been developed. Numerical investigations on the performance of these elements have been carried out through standard test problems for validation purpose. Comparisons involving theoretical closed form solutions as well as results obtained with existing finite elements have also been made. It is found that the new elements perform well in all the situations considered. Solutions in all the cases converge correctly to the exact values. In many cases, convergence is faster when compared with other existing finite elements. The behaviour of field consistent elements would definitely generate a great deal of interest amongst the users of the finite elements. |
| Description: | Department of Ship Technology, Cochin University of Science and Technology |
| URI: | http://dyuthi.cusat.ac.in/purl/2121 |
| Files | Size |
|---|---|
| Dyuthi-T0411.pdf | (1.799Mb) |
| Abstract: | Important issues related to femtosecond (fs) pulses and its relevance to this thesis are discussed. A fundamental characteristic, like the timebandwidth product for fs pulses is decribed in detail. A brief review of generation of ultrashort pulses and its propagation through an optically transparent media are presented. Interaction of strong pulses with matter and different ionization processes are also described. An overview of the thesis is presented at the end |
| URI: | http://dyuthi.cusat.ac.in/purl/5097 |
| Files | Size |
|---|---|
| Dyuthi- T 2163.pdf | (11.76Mb) |
| Description: | Dept.of Applied Economics,Cochin University of Science and Technology |
| URI: | http://dyuthi.cusat.ac.in/purl/2783 |
| Files | Size |
|---|---|
| Dyuthi-T0806.pdf | (2.129Mb) |
| Abstract: | Financial inclusion for inclusive growth is central to the developmental philosophy of most of the nations over the past decade. It has been a priority for policy makers and regulators in financial sector development for improving access and usage of financial services to achieve comprehensive financial inclusion. The initiatives taken towards financial inclusion can promote a more effective and efficient process to achieve significant improvements in financial inclusion are to establish and achieve shared and sustainable development and growth. Realising this, an increasing number of countries are committing to promote financial inclusion, encouraged by the growing body of country level experiences (World Bank, 2012). Financial inclusion basically means, broad based growth through participation as well as sharing the benefits from the growth process along with the under privileged and marginal segments of the economy. Evidence suggests that it has substantial benefits for equitable and sustainable growth. Inclusive growth ensures that while economy grows rapidly, all segments of society are involved in this growth process, ensuring equal opportunities, devoid of any regional or sectoral disparitiesIt is widely acknowledged that the objective ofinclusive growth is accomplished through the process of financial inclusion. Financial inclusion envisages bringing everyone, irrespective of financial status, into the banking fold for the individual progress and development and thereby achieving comprehensive growth with equity |
| URI: | http://dyuthi.cusat.ac.in/purl/5085 |
| Files | Size |
|---|---|
| Dyuthi- 2151.pdf.pdf | (2.971Mb) |
| Abstract: | Today India is seeking a speedy transformation of her semi-stagnant economy to a dynamic one by means of economic planning in a democratic set up. In the context of this growth oriented endeavour public sector has a vital role to play. After three decades of planned development, it has become important that India must make fresh appraisals on the role of public sector in the economic renaissance of the country. Almost no comprehensive study has been made on this vital segment of the economy vis-a-vis the growth economics. This study is an attempt to fill this need in a very modest way. It presents the subject in a new perspective. An earnest attempt is made to reveal the critical problems inhibiting the growth of the public sector from a new angle which focusses the spot-light on the economics of development. |
| Description: | School of management studies, Cochin University of Science And Technology |
| URI: | http://dyuthi.cusat.ac.in/purl/3311 |
| Files | Size |
|---|---|
| Dyuthi-T1285.pdf | (33.10Mb) |
| URI: | http://dyuthi.cusat.ac.in/purl/1247 |
| Files | Size |
|---|---|
| Wilson P R 1982.PDF | (552.0Kb) |
| Abstract: | Time resolved optical emission spectroscopy is employed to study the expansion dynamics of C2 species in a graphite plasma produced during the Nd : YAG ablation. At low laser fluences a single peak distribution with low kinetic energy is observed. At higher fluences a twin peak distribution is found. It has been noted that these double peak time of flight distribution splits into a triple peak structure at distances >_ 17mm from the target surface. The reason for the occurrence of multiple peak is due to different formation mechanisms of C2 species |
| URI: | http://dyuthi.cusat.ac.in/purl/2454 |
| Files | Size |
|---|---|
| Dyuthi-P0315.pdf | (377.4Kb) |
Dyuthi Digital Repository Copyright © 2007-2011 Cochin University of Science and Technology. Items in Dyuthi are protected by copyright, with all rights reserved, unless otherwise indicated.