Ceramic dielectric resonators in the BaO-RE2O3-TiO2 (RE = rare earth) system have been
prepared by the conventional solid state ceramic route. The dielectric properties have been
tailored by substitution of different rare earth oxides and by bismuth oxide addition. The
dielectric constants increased with Bi addition whereas the 0 decreased. The temperature
coefficient of the resonant frequency improved with bismuth addition
Ceramic dielectric resonators in the BaO-RE2O3-TiO2 (RE=rare earth) system have been
prepared by the conventional solid state ceramic route. The dielectric properties have been
tailored by substitution of different rare earth oxides and by bismuth oxide addition. The
dielectric constants increased with Bi addition whereas the Q decreased. The temperature
coeffecient of the resonant frequency improved with bismuth addition.
Microwave dielectric ceramics based on GdTiNb,-,.Ta,O6 and Sml _.,Y,TiTa06 have been prepared by conventional solid state
method . The GdTiTaO6 and SmTiTaO6 have aeschenite structure with positive rr and GdTiNbO6 and YTiTaO6 have euxenite
structure with negative rr. The rr of the ceramics has been tuned by preparing solid solution phases between the aeschynites and
euxenites for a possible zero rr material . It is observed that GdTiNbt_YTa.,O6 undergoes a phase transition from aeschynite to
euxenite when x=0.75 and in Sml-,YxTiTa06 for x= 0.73. The microwave dielectric properties change abruptly near the transition
region . The rr value approaches zero near the phase transition region while the samples have poor sinterability and poor quality
factor . The unloaded quality factor, dielectric constant and the sign of rr of the solid solution phases are found to depend on the
average ionic radius of the rare earth ion in RE ,-5RE',TiTaO6. The boundary of the euxenite-aeschynite phase transition occurs at
an average ( RE) ionic radius of 0.915 A in Sm,_, Y,.TiTaO6 solid solution phases
V P N Nampoori; Mohammed Yusuff,K K; Arun,V; Mathew,S; Robinson,P P; Jose,M(Elsevier, Journal of Dyes and Pigments, March 20, 2010)
[+]
[-]
Abstract:
The Schiff base, 3-hydroxyquinoxaline-2-carboxalidine-4-aminoantipyrine, was synthesized by the
condensation of 3-hydroxyquinoxaline-2-carboxaldehyde with 4-aminoantipyrine. HPLC, FT-IR and NMR
spectral data revealed that the compound exists predominantly in the amide tautomeric form and
exhibits both absorption and fluorescence solvatochromism, large stokes shift, two electron quasireversible
redox behaviour and good thermal stability, with a glass transition temperature of 104oC. The
third-order non-linear optical character was studied using open aperture Z-scan methodology employing
7 ns pulses at 532 nm. The third-order non-linear absorption coefficient, b, was 1.48 x 10-6 cm W-1 and
the imaginary part of the third-order non-linear optical susceptibility, Im c(3), was 3.36 x10-10 esu. The
optical limiting threshold for the compound was found to be 340 MW cm-2.
Mohammed Yusuff, K K; V P N Nampoori; Arun,V; Mathew,S; Robinson,P; Jose,M(Elsevier, Journal of Dyes and Pigments, March 20, 2010)
[+]
[-]
Abstract:
The Schiff base, 3-hydroxyquinoxaline-2-carboxalidine-4-aminoantipyrine, was synthesized by the
condensation of 3-hydroxyquinoxaline-2-carboxaldehyde with 4-aminoantipyrine. HPLC, FT-IR and NMR
spectral data revealed that the compound exists predominantly in the amide tautomeric form and
exhibits both absorption and fluorescence solvatochromism, large stokes shift, two electron quasireversible
redox behaviour and good thermal stability, with a glass transition temperature of 104 oC. The
third-order non-linear optical character was studied using open aperture Z-scan methodology employing
7 ns pulses at 532 nm. The third-order non-linear absorption coefficient, b, was 1.48 x 10-6 cm W-1 and
the imaginary part of the third-order non-linear optical susceptibility, Im c(3), was 3.36x10-10 esu. The
optical limiting threshold for the compound was found to be 340 MW cm-2.
Surendran,K P; Santha,N; Mohanan,P; Sebastian,M T(The European Physical Journal, 2004)
[+]
[-]
Abstract:
The microwave dielectric properties of ZnAl2O4 spinels were investigated and their properties
were tailored by adding different mole fractions of Ti02. The samples were synthesized using the mixed
oxide rout.e. The phase purity and crystal structure were identified using X-ray diffraction technique.
The sintered specimens were characterized in the microwave frequency range (3-13 GHz). The ZnA12O4
ceramics exhibited interesting dielectric properties (dielectric constant (e,.) = 8.5, unloaded quality factor
(Q.) = 4590 at 12.27 GHz and temperature coefficient of resonant frequency (Tf) = -79 ppm/°C).
Addition of Ti02 into the spinel improved its properties and the Tf approached zero for 0.83ZnAl2O4-
0.17TiO2• This temperature compensated composition has excellent microwave dielectric properties (Cr _
12.67, Q, = 9950 at 10.075 GHz) which can be exploited for microwave substrate applications
Harilal, S S; Bindhu, C V; Nampoori, V P N; Vallabhan, C P G(Applied Spectroscopy, 1998)
[+]
[-]
Abstract:
Spectroscopic studies of laser -induced plasma from a high-temperature
superconducting material, viz., YBa2Cu3O7 (YBCO), have
been carried out. Electron temperature and electron density measurements
were made from spectral data. The Stark broad ening of
emission lines was used to determine the electron density, and the
ratio of line in tensities was exploited for the determination of electron
temperature. An initial electron temperature of 2.35 eV and
electron density of 2.5 3 1017 cm2 3 were observed. The dependence
on electron temperature and density on different experimental parameters
such as distance from the target, delay time after the in itiation
of the plasm a, and laser irradiance is also discussed in detail.
Index Headings: Laser -plasma spectroscopy; Plasma diagnostics;
Emission spectroscop y; YBa2Cu3O7.
Harilal, S S; Issac, Riju C; Bindhu, C V; Nampoori, V P N; Vallabhan, C P G(American Institute of Physics, September 15, 1996)
[+]
[-]
Abstract:
Laser ablation of graphite has been carried out using 1.06mm radiation from a Q-switched Nd:YAG
laser and the time of flight distribution of molecular C2 present in the resultant plasma is
investigated in terms of distance from the target as well as laser fluences employing time resolved
spectroscopic technique. At low laser fluences the intensities of the emission lines from C2 exhibit
only single peak structure while beyond a threshold laser fluence, emission from C2 shows a twin
peak distribution in time. The occurrence of the faster velocity component at higher laser fluences
is explained as due to species generated from recombination processes while the delayed peak is
attributed to dissociation of higher carbon clusters resulting in the generation of C2 molecule.
Analysis of measured data provides a fairly complete picture of the evolution and dynamics of
C2 species in the laser induced plasma from graphite.
Harilal, S S; Radhakrishnan, P; Nampoori, V P N; Vallabhan, C P G(American Institute of Physics, June , 1994)
[+]
[-]
Abstract:
YBa2Cu307 target was laser ablated, and the time-of-flight (TOF) distributions of Y, Y+., and YO in
the resultant plasma were investigated as functions of distance from the target and laser energy
density using emission spectroscopy. Up to a short distance from the target (-1.5 cm), TOF
distributions show twin peaks for Y and YO, while only single-peak distribution is observed for Y+.
At greater distances (>1.5 cm) all of them exhibit single-peak distribution. The twin peaks are
assigned to species corresponding to those generated directly/m the vicinity of target surface and to
those generated from collisional/recombination process.
Paulose,C S; Thliveris,J A; Dakshinamurti,K; Viswanathan,M(Department of Biotechnology, 1989)
[+]
[-]
Abstract:
We have studied testicular function in the biotin-
deficient rat biochemically and morphologically.
Serum testosterone and luteinizing hormone (LH) levels
were decreased significantly in the deficient rats. Administration
of biotin or gonadotropins to the deficient rats
reversed this decrease in serum testosterone. There was no
difference in the serum cholesterol level between the control
and biotin-deficient rats. A significant degree of sloughing
of seminiferous tubule germinal epithelium was noticed
in the biotin-deficient rat testes. Biotin treatment of biotindeficient
rats reversed this condition whereas testosterone
treatment was without any effect. The development and
maintenance of morphological and functional integrity of
the seminiferous tubules appears to require a biotin-mediated
step in addition to testosterone.
Sajan D, George; Achamma, Kurian; Martin, Lase; Nampoori, V P N; Vallabhan, C P G(SPIE, 2001)
[+]
[-]
Abstract:
An open cell photoacoustic configuration has been employed to evaluate the thermal diffusivity of pure InP as well as InP doped with sulphur and iron. Chopped optical radiation at 488 nm from an Ar-ion laser has been used to excite photoacoustic signals which been detected by a sensitive electret microphone. Thermal diffusivity value have been calculated from phase versus chopping frequency plots. Doped sample are found to show a reduced value for thermal diffusivity in comparison with intrinsically pure sample. The results have been interpreted in terms of the mechanisms of heat generation and transmission in semiconductors.
Joseph, L K; Sanjay, G; Suja, H; Sugunan, S; Nampoori, V P N; Radhakrishnan, P(Taylor & Francis, April 1, 2009)
[+]
[-]
Abstract:
Thermal diffusivity (TD) measurements were performed on some industrially
important dyes – auramine O (AO), malachite green and methylene blue (MB) –
adsorbed K-10 montmorillonites using photoacoustic method. The TD value for
the dye-adsorbed clay mineral was observed to change with a variation in dye
concentration. The contribution of the dye towards TD was also determined. The
repeatedly adsorbed samples with MB and AO exhibited a lower TD than the
single-adsorbed samples. TD values of sintered MB samples were also obtained
experimentally. These sintered samples exhibit a higher TD, although they show
a trend similar to that of non-sintered pellets. A variation in dye concentration
and sintering temperature can be used for tuning the TD value of the clay mineral
to the desired level.
Annieta Philip, K; Lyjo K, Joseph; Litty M, Irimpan; Bindu, Krishnan; Radhakrishnan, P; Nampoori, V P N; Raghu, Natarajan(WILEY-VCH Verlag, 2007)
[+]
[-]
Abstract:
Thermal characterization of alumina–zirconia and zirconia ceramic tapes using a photoacoustic technique is presented. A transmission-mode geometry is employed for the measurement of thermal diffusivity while a reflection-mode geometry is used for the measurement of thermal effusivity. In both these geometries, the same open photoacoustic cell is used. From the measured values of thermal diffusivity and thermal effusivity, the thermal conductivity value has also been evaluated.
Radhakrishnan,P; V P N Nampoori; Girijavallabhan,C P; Anantharaman,M R; Sajan,D George; Saravanan,S; Venkatachalam,S(Physical Review, American Physical Society, June 8, 2004)
[+]
[-]
Abstract:
Thermal diffusivity of the composites of camphor sulphonic acid (CSA) doped polyaniline (PANI) and its
composites with cobalt phthalocyanine (CoPc) has been measured using open cell photoacoustic technique.
Analysis of the data shows that the effective thermal diffusivity value can be tuned by varying the relative
volume fraction of the constituents. It is seen that polaron assisted heat transfer mechanism is dominant in CSA
doped PANI and these composites exhibit a thermal diffusivity value which is intermediate to that of CSA
doped PANI and CoPc. The results obtained are correlated with the electrical conductivity and hardness
measurements carried out on the samples
Girijavallabhan, C P; Radhakrishnan, P; V P N Nampoori; Sajan, D George; Saravanan, S; Venkatachalam, S(Physical Review, American Physical Society, June 8, 2004)
[+]
[-]
Abstract:
Thermal diffusivity of the composites of camphor sulphonic acid (CSA) doped polyaniline (PANI) and its
composites with cobalt phthalocyanine (CoPc) has been measured using open cell photoacoustic technique.
Analysis of the data shows that the effective thermal diffusivity value can be tuned by varying the relative
volume fraction of the constituents. It is seen that polaron assisted heat transfer mechanism is dominant in CSA
doped PANI and these composites exhibit a thermal diffusivity value which is intermediate to that of CSA
doped PANI and CoPc. The results obtained are correlated with the electrical conductivity and hardness
measurements carried out on the samples.
V P N Nampoori; Radhakrishnan,P; Girijavallabhan,C P; Anantharaman,M R; Sajan,D George; Saravanan,S; Venkatachalam,S(Physical Review, American Physical Society, June 8, 2004)
[+]
[-]
Abstract:
Thermal diffusivity of the composites of camphor sulphonic acid (CSA) doped polyaniline (PANI) and its
composites with cobalt phthalocyanine (CoPc) has been measured using open cell photoacoustic technique.
Analysis of the data shows that the effective thermal diffusivity value can be tuned by varying the relative
volume fraction of the constituents. It is seen that polaron assisted heat transfer mechanism is dominant in CSA
doped PANI and these composites exhibit a thermal diffusivity value which is intermediate to that of CSA
doped PANI and CoPc. The results obtained are correlated with the electrical conductivity and hardness
measurements carried out on the samples
Anantharaman,M R; V P N Nampoori; Radhakrishnan,P; Girijavallabhan,C P; Sajan,D George; Saravanan, S; Venkatachalam,S(Physical Review, American Physical Society, June 8, 2004)
[+]
[-]
Abstract:
Thermal diffusivity of the composites of camphor sulphonic acid (CSA) doped polyaniline (PANI) and its
composites with cobalt phthalocyanine (CoPc) has been measured using open cell photoacoustic technique.
Analysis of the data shows that the effective thermal diffusivity value can be tuned by varying the relative
volume fraction of the constituents. It is seen that polaron assisted heat transfer mechanism is dominant in CSA
doped PANI and these composites exhibit a thermal diffusivity value which is intermediate to that of CSA
doped PANI and CoPc. The results obtained are correlated with the electrical conductivity and hardness
measurements carried out on the samples
Radhakrishnan, P; V P N Nampoori; Girijavallabhan, C P; Sajan, D George(Journal of Physics D : Applied Physics, Institute of Physics Publishing, April 2, 2003)
[+]
[-]
Abstract:
An open photoacoustic cell operating in the low range of chopping
frequency has been employed to evaluate the thermal diffusivity values of
intrinsic InP and InP doped with S, Sn and Fe. The experimental set-up is
calibrated by the evaluation of thermal diffusivity value of pure Si and
GaAs. The present investigation shows that doped samples show a reduced
value for thermal diffusivity compared to intrinsic sample. From the
analysis of data it is also seen that nature of dopant clearly influences the
thermal diffusivity value of semiconductors. The results are explained in
terms of phonon assisted heat transfer mechanism in semiconductors
V P N Nampoori; Radhakrishnan, P; Girijavallabhan, C P; Sajan, D George(Journal of Physics D : Applied Physics, Institute of Physics Publishing, April 2, 2003)
[+]
[-]
Abstract:
An open photoacoustic cell operating in the low range of chopping
frequency has been employed to evaluate the thermal diffusivity values of
intrinsic InP and InP doped with S, Sn and Fe. The experimental set-up is
calibrated by the evaluation of thermal diffusivity value of pure Si and
GaAs. The present investigation shows that doped samples show a reduced
value for thermal diffusivity compared to intrinsic sample. From the
analysis of data it is also seen that nature of dopant clearly influences the
thermal diffusivity value of semiconductors. The results are explained in
terms of phonon assisted heat transfer mechanism in semiconductors