| Abstract: | A comparative study on the anisole methylation with methanol over lanthanum-promoted Sn02 catalyst and its sulfate-doped analogue is presented. A maximum 2.6-xylenol selectivity of 82% was achieved at 400 degreeC under optimized conditions at an anisole conversion of 65% over lanthanum-promoted Sn02 catalyst. The sulfate modification resulted in the dealkylation of anisole to phenol followed by several unselective side reactions due to the creation of strong acid sites. The activity of lanthanum-modified tin oxide catalysts in the selective formation of 2.6-xylenol is ascribed to the presence of weak Lewis acid sites and comparatively stronger basic sites. |
| URI: | http://dyuthi.cusat.ac.in/purl/2170 |
| Files | Size |
|---|---|
| Dyuthi-SS10.pdf | (241.3Kb) |
| Abstract: | In this paper, microstrip lines magnetically coupled to splitring resonators (SRRs) are conquved to electromagnetic bundgup (EBG) nr,rrostrip lines in terns q/ their stop-heard penjbrnmrnce and dimensions. In bath types o/ trunsmis•siou lines, signal propagation is inhibited in it certain jequency bwuL For EBG microstrip lines, the central frequency of such a forbidden band is determined by the period of the structure, whereas in SRR-hased microstrip lines the position of the frequency gap depends on the quasi-static resonant frequency of the rings. The main relevant conrributiun of this paper is to provide a tuning procedure to control the gap width in SRR microstrip lines, and to show that by using SRRs, device dimensions ale much smaller than those required by EBGs in order to obtain similar stop-banal performance. This has been demonstrated by fill-wave electromagnetic simulations and experimentally verified from the characterization ql two fabricated microstrip lines: one with rectangular SRRs etched on the upper substrate side, and the other with a periodic perturbation cf'strip width. For similar rejection and 1-(;H,. gap width centered at 4.5 Gllz, it has been found that the SRR microstrip line is•,fve times shorter. In addition, no ripple is appreciable in the allowed band for the .SRR-hared structure, whereas due to dispersion, certain mismatch is expected in the EBG prototype. Due to the high-frequency selectivity, controllable gap width, and small dimensions, it is believed that SRR coupled to planar transmission lines can have an actual impact on the design of stop-band filters compatible with planar technology, and can be an alternative to present solutions based on distributed approaches or EBG |
| URI: | http://dyuthi.cusat.ac.in/purl/1421 |
| Files | Size |
|---|---|
| Comparison of e ... s stop band structures.PDF | (686.9Kb) |
| Abstract: | Microwave properties of conductive polymers is crucial because of their wide areas of applications such as coating in reflector antennas, coating in electronic equipments, firequenry selective .surfaces, EMI materials, satellite communication links, microchip antennas, and medical applications. This work involves a comparative study of dielectric properties of selected conducting polymers such as polyaniline. poly(3,4-eth),lenedio.syt2iophene), polvthiophene, polvpvrrole. and pohparaphenylene diazomethine (PPDA) in microwave and DC,fields. The inicrowave properties such as dielectric constant, dielectric loss. absorption coefficient, heating coefficient, skin depth, and conductivity in the microwave frequency (S hand), and DC fields were compared. PEDOT and polccuiiline were found to exhibit excellent properties in DC field and microwave frequencies, which make thein potential materials in many of the alorenientioned applications |
| URI: | http://dyuthi.cusat.ac.in/purl/804 |
| Files | Size |
|---|---|
| K.Lakshmi and o ... microwave....June2007.PDF | (4.073Mb) |
| Abstract: | This paper compares statistical technique of paraphrase identification to semantic technique of paraphrase identification. The statistical techniques used for comparison are word set and word-order based methods where as the semantic technique used is the WordNet similarity matrix method described by Stevenson and Fernando in [3]. |
| Description: | 2012 International Conference on Data Science & Engineering (ICDSE) |
| URI: | http://dyuthi.cusat.ac.in/purl/4109 |
| Files | Size |
|---|---|
| Comparison of S ... aphrase Identification.pdf | (88.92Kb) |
| Abstract: | In this paper, a comparison study among three neuralnetwork algorithms for the synthesis of array patterns is presented. The neural networks are used to estimate the array elements' excitations for an arbitrary pattern. The architecture of the neural networks is discussed and simulation results are presented. Two new neural networks, based on radial basis functions (RBFs) and wavelet neural networks (WNNs), are introduced. The proposed networks offer a more efficient synthesis procedure, as compared to other available techniques |
| URI: | http://dyuthi.cusat.ac.in/purl/1413 |
| Files | Size |
|---|---|
| Comparison stud ... using neural networks.PDF | (379.2Kb) |
| Abstract: | The principal objective of this study was to explore the compatibility of a blend of two synthetic elastomers viz., ethylene-propylene-diene rubber (EPDM) and chlorobutyl rubber (CIIR). Various commercial grades of EPDM were blended with a specific grade of CIIR at different proportions. The mechanical properties such as tensile strength, tear strength, ageing resistance, etc. were studied. On the basis of the observed physical properties, two particular grades of EPDM were found to be compatible with CIIR. Differential scanning calorimetry and scanning electron microscopy confirmed the results. Chlorosulphonated polyethylene was added as a compatibilizing agent to overcome the phase separation of the other two incompatible grades of EPDM in blending with CIIR. The results revealed that the addition of compatibilizer greatly improves the compatibility and thereby the properties of the blends. |
| URI: | http://dyuthi.cusat.ac.in/xmlui/purl/2001 |
| Files | Size |
|---|---|
| Compatibility studies on....pdf | (403.3Kb) |
| Abstract: | Bank switching in embedded processors having partitioned memory architecture results in code size as well as run time overhead. An algorithm and its application to assist the compiler in eliminating the redundant bank switching codes introduced and deciding the optimum data allocation to banked memory is presented in this work. A relation matrix formed for the memory bank state transition corresponding to each bank selection instruction is used for the detection of redundant codes. Data allocation to memory is done by considering all possible permutation of memory banks and combination of data. The compiler output corresponding to each data mapping scheme is subjected to a static machine code analysis which identifies the one with minimum number of bank switching codes. Even though the method is compiler independent, the algorithm utilizes certain architectural features of the target processor. A prototype based on PIC 16F87X microcontrollers is described. This method scales well into larger number of memory blocks and other architectures so that high performance compilers can integrate this technique for efficient code generation. The technique is illustrated with an example |
| Description: | International Journal of Software Engineering and Its Applications Vol. 6, No. 1, January, 2012 |
| URI: | http://dyuthi.cusat.ac.in/purl/4668 |
| Files | Size |
|---|---|
| A Compiler Inte ... ry Embedded Processors.pdf | (577.3Kb) |
| Abstract: | This paper reports the synthesis of a series of six new polystyrene anchored metal complexes of Co(II), Fe(III), Ni(II), Cu(II), Zn(II), and dioxouanium(VI) using the polystyrene anchored Schiff base of 2-nitrobenzaldehyde and the corresponding metal salts. The metal salts used were anhydrous FeCl3, CoCl2 Æ 6H2O, Ni(CH3COO)2 Æ 4H2O, Cu(CH3- COO)2 Æ H2O, Zn(CH3COO)2 Æ 2H2O, and UO2(CH3COO) Æ 2H2O. Physico chemical characterizations have been made from diffuse reflectance and vibrational spectra, elemental analysis, magnetic measurements, and TG studies. The elemental analysis suggest a 1:2 metal:ligand ratio when the complexation has carried out at 70 C for about 12 h reflux. The ligand is monodentate and coordinates through the azomethine nitrogen. The Fe(III), Co(II), Ni(II), and Cu(II) complexes are all paramagnetic whereas Zn(II) and U(VI) are diamagnetic. Zn(II) is assigned a tetrahedral structure, Cu(II) and Co(II) are assigned a square planar structure and Fe(III), Ni(II), and U(VI) are all assigned an octahedral structure. The polystyrene anchored ligand has been developed as an excellent reagent for the removal of Cu(II). Optimum conditions have been developed for the removal of metal ion from solutions by studying the effect of change of concentration of metal ion, ligand, effect of pH, time of reflux, and interference effect of other ions. It was found that within a span of 20 min it is possible to remove 90% of the metal ion from a 30 ppm metal ion solution in the pH range 4–5.5. |
| URI: | http://dyuthi.cusat.ac.in/purl/518 |
| Files | Size |
|---|---|
| REACT2135.pdf | (271.9Kb) |
| Abstract: | n this paper, a time series complexity analysis of dense array electroencephalogram signals is carried out using the recently introduced Sample Entropy (SampEn) measure. This statistic quantifies the regularity in signals recorded from systems that can vary from the purely deterministic to purely stochastic realm. The present analysis is conducted with an objective of gaining insight into complexity variations related to changing brain dynamics for EEG recorded from the three cases of passive, eyes closed condition, a mental arithmetic task and the same mental task carried out after a physical exertion task. It is observed that the statistic is a robust quantifier of complexity suited for short physiological signals such as the EEG and it points to the specific brain regions that exhibit lowered complexity during the mental task state as compared to a passive, relaxed state. In the case of mental tasks carried out before and after the performance of a physical exercise, the statistic can detect the variations brought in by the intermediate fatigue inducing exercise period. This enhances its utility in detecting subtle changes in the brain state that can find wider scope for applications in EEG based brain studies. |
| URI: | http://dyuthi.cusat.ac.in/purl/2602 |
| Files | Size |
|---|---|
| Dyuthi-P0162.pdf | (1.121Mb) |
| Abstract: | A new polymer matrix sensitized with methylene blue for use as an optical recording material is described here. The characterization is done to determine the optimal recording conditions. These films need no chemical development and are found to be stable for several months. The matrix has excellent shelf life and needs an exposure only as short as 20 s. Direct imaging was done on this material. |
| URI: | http://dyuthi.cusat.ac.in/purl/857 |
| Files | Size |
|---|---|
| M Ushamani and ... methylene...,April2002.PDF | (4.151Mb) |
| Abstract: | Dielectric properties of polyaniline at different frequencies were studied. Cavity perturbation technique was employed for the study. Poly aniline in the powder and pelletised forms were prepared under different environmental conditions. Different samples of poly aniline exhibit high conductivity. However, the conductivity of samples prepared under different environmental conditions is found to vary. All the samples in the powder form have high conductivity irrespective of the method of preparation. The high conductivity at microwave frequency makes it possible to be used for developing microwave components like filters. |
| URI: | http://dyuthi.cusat.ac.in/purl/868 |
| Files | Size |
|---|---|
| S Biju Kumar an ... ermitivity and...,2001.PDF | (2.649Mb) |
| Abstract: | Dielectric properties of polyaniline at different frequencies were studied. Cavity perturbation technique was employed for the study. Poly aniline in the powder and pelletised forms were prepared under different environmental conditions. Different samples of poly aniline exhibit high conductivity. However. the conductivity of samples prepared under different environmental conditions is found to vary. All the samples in the powder form have high conductivity irrespective of the method of preparation. The high conductivity at microwave frequency makes it possible to be used for developing microwave components like filters. |
| URI: | http://dyuthi.cusat.ac.in/purl/2978 |
| Files | Size |
|---|---|
| Dyuthi-P00413.pdf | (620.0Kb) |
| Abstract: | The room temperature AC conductivity σ(ω) of amorphous AsSe samples with various compositions have been measured in the 103 -106 Hz frequency range. The results indicate that ac conductivity is proportional to n with n=0.89±.01 in the 103 –106 Hz frequency range. Consideration of different models for the frequency –dependent conductivity leads to thermally activated hopping as the most likely process |
| Description: | International Journal of Scientific and Research Publications, Volume 4, Issue 5, May 2014 |
| URI: | http://dyuthi.cusat.ac.in/purl/4649 |
| Files | Size |
|---|---|
| Composition Dep ... tivity in AsSe samples.pdf | (217.7Kb) |
| Abstract: | We propose a novel, simple, efficient and distribution-free re-sampling technique for developing prediction intervals for returns and volatilities following ARCH/GARCH models. In particular, our key idea is to employ a Box–Jenkins linear representation of an ARCH/GARCH equation and then to adapt a sieve bootstrap procedure to the nonlinear GARCH framework. Our simulation studies indicate that the new re-sampling method provides sharp and well calibrated prediction intervals for both returns and volatilities while reducing computational costs by up to 100 times, compared to other available re-sampling techniques for ARCH/GARCH models. The proposed procedure is illustrated by an application to Yen/U.S. dollar daily exchange rate data. |
| URI: | http://dyuthi.cusat.ac.in/purl/2856 |
| Files | Size |
|---|---|
| Dyuthi-P00399.pdf | (427.5Kb) |
| Abstract: | The median (antimedian) set of a profile π = (u1, . . . , uk) of vertices of a graphG is the set of vertices x that minimize (maximize) the remoteness i d(x,ui ). Two algorithms for median graphs G of complexity O(nidim(G)) are designed, where n is the order and idim(G) the isometric dimension of G. The first algorithm computes median sets of profiles and will be in practice often faster than the other algorithm which in addition computes antimedian sets and remoteness functions and works in all partial cubes |
| Description: | Algorithmica (2010) 57: 207–216 DOI 10.1007/s00453-008-9200-4 |
| URI: | http://dyuthi.cusat.ac.in/purl/4193 |
| Files | Size |
|---|---|
| Computing median and antimedian sets in median.pdf | (290.4Kb) |
| Abstract: | Automobile Industry in India is influenced by the presence of national and multi-national manufacturers. The presence of many manufacturers and brands in the state provides many choices to the customer. The current market for car manufacturers has been transformed from a monopoly of one or two manufacturers in the seventies to oligopoly of many manufacturers in the current marketing scenario. The main objective of the research paper is to explore and conceptualize various parameters and develop a model, which influence the purchase patterns of passenger cars in the State of Kerala. Thus, the main purpose of this paper is to come up with a model, which shall facilitate further study on the consumer purchase behaviour patterns of passenger car owners in the State of Kerala, India. The author intends to undertake further quantitative analysis to verify and validate the model so developed. The main methods used for this paper are secondary research on available material, depth interview of car dealers, car financing agencies and car owners in the city of Cochin, in Kerala State in India. The depth interviews were conducted with the use of prepared questionnaire for car dealers, car customers and car financing agencies. The findings resulted in the identification of the parameters that influence the consumer purchase behaviour of passenger cars and the formulation of the model, which will be the basis for the further research of the author. The paper will be of tremendous value to the existing and new car manufacturers both indigenous and foreign, to formalize and strategies their policies towards an effective marketing strategy, so as to market their models in the State, which is known for its high literacy, consumerism and higher educational penetration |
| Description: | IJRFM Volume 1, Issue 5 (September, 2011) |
| URI: | http://dyuthi.cusat.ac.in/purl/4493 |
| Files | Size |
|---|---|
| Conceptualisati ... iour Of Passenger Cars.pdf | (158.3Kb) |
| Abstract: | Conducting polymers are excellent microwave absorbers and they show technological advantage when compared with inorganic electromagnetic absorbing materials, being light weight , easily processable, and the ability of changing the electromagnetic properties with nature and amount of dopants, synthesis conditions, etc. In this paper we report the synthesis, dielectric properties, and expected application of conducting composites based on polyaniline (PAN). Cyclohexanone soluble conducting PAN composites of microwave conductivity 12.5 S/m was synthesized by the in situ polymerization of aniline in the presence of emulsion grade polyvinyl chloride. The dielectric properties of the composites, especially the dielectric loss, conductivity, dielectric heating coefficient , absorption coefficient, and penetration depth, were studied using a HP8510 vector network analyzer. The microwave absorption of the composites were studied at different frequency bands i.e, S, C, and X bands (2-12 GHz). The absorption coefficient was found to be higher than 200 m -' and it can be used for making microwave absorbers in space applications . |
| URI: | http://dyuthi.cusat.ac.in/purl/797 |
| Files | Size |
|---|---|
| Honey John and ... lyaniline composites...PDF | (3.966Mb) |
| Abstract: | Conducting polymers are excellent microwave absorbers and they show technological advantage when compared with inorganic electromagnetic absorbing materials, being light weight , easily processable, and the ability of changing the electromagnetic properties with nature and amount of dopants, synthesis conditions, etc. In this paper we report the synthesis, dielectric properties, and expected application of conducting composites based on polyaniline (PAN). Cyclohexanone soluble conducting PAN composites of microwave conductivity 12.5 S/m was synthesized by the in situ polymerization of aniline in the presence of emulsion grade polyvinyl chloride. The dielectric properties of the composites, especially the dielectric loss, conductivity, dielectric heating coefficient , absorption coefficient, and penetration depth, were studied using a HP8510 vector network analyzer. The microwave absorption of the composites were studied at different frequency bands i.e, S, C, and X bands (2-12 GHz). The absorption coefficient was found to be higher than 200 m -' and it can be used for making microwave absorbers in space applications |
| URI: | http://dyuthi.cusat.ac.in/purl/875 |
| Files | Size |
|---|---|
| Honey John and ... lyaniline composites...PDF | (3.966Mb) |
| Abstract: | Electrical properties of ac plasma polymerized aniline thin films are investigated with a view of determining the dominant conduction mechanism. The current–voltage (I–V) characteristics in symmetric and asymmetric electrode configuration for polyaniline thin films in the thickness range from 1300 to 2000 A ° are investigated. From the studies on asymmetric electrode configuration, it is found that the dominant conduction mechanism in these films is of Schottky type |
| Description: | Materials Letters 57 (2003) 2253– 2257 |
| URI: | http://dyuthi.cusat.ac.in/purl/4366 |
| Files | Size |
|---|---|
| Conduction mech ... zed aniline thin films.pdf | (104.7Kb) |
| Abstract: | The recent boom in wireless communication industry, especially in the area of cellular telephony and wireless data communication, has led to the increased demand for multi band antennas. In such applications the issues to be addressed are, wide bandwidth and gain, while striving for miniature geometry. A dual frequency configuration useful in GSM1800 and Blue tooth, is one that operates with similar properties, both in terms of reflection and radiation characteristics, in the two bands of interest. Dual frequency operations can be realized by exciting the Microstrip Patch Antenna (MPA) using a single feed [1] or dual feed [2]. In this paper, Conformal FDTD[3] method with Perfect Magnetic Conductor (PMC) applied along the plane of symmetry [4] is used to study the characteristics of an Octagonal MPA. The theoretical results are compared against the experimental and IE3D™ simulated results |
| Description: | Antennas and Propagation Society International Symposium, 2007 IEEE,PP 5259-5262 |
| URI: | http://dyuthi.cusat.ac.in/purl/4335 |
| Files | Size |
|---|---|
| Conformal FDTD ... crostrip Patch antenna.pdf | (343.7Kb) |
Dyuthi Digital Repository Copyright © 2007-2011 Cochin University of Science and Technology. Items in Dyuthi are protected by copyright, with all rights reserved, unless otherwise indicated.