Abstract: | Phenolic resins suffer from the presence of microvoids on curing. This often leads to less than satisfactory properties in the cured resin. This disadvantage has limited the use of phenolic resins to some extent. This study is an attempt to improve the mechanical properties of the phenolic resol resins by chemical modification aimed at reducing the microvoid population. With this end in view various themoset resins synthesised under predetennined conditions have been employed for modifying phenolic resols. Such resins include unsaturated polyester, epoxy and epoxy novolac prepolymers. The results establish the effectiveness of these resins for improving the mechanical properties of phenolics. Experimental and analytical techniques used include FTIR, DMA, TGA, SEM and mechanical property evaluation. While most of the modifier resins employed give positive results the effect of adding UP is found to be surprising as well as impressive. |
Description: | Department of Polymer Science and Rubber Technology, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/3088 |
Files | Size |
---|---|
Dyuthi-T1062.pdf | (6.986Mb) |
Abstract: | The main aim of the study was to optimise the reactive extrusion conditions in the conventional modification processes of polyethylenes in a single screw extruder.The optimum conditions for peroxide crosslinking of low density polyethylene (LDPE), linear low density polyethylene (LLDPE) and their blend were determined in a torque rheometer. The actual reactive extrusion was performed in a laboratory single screw extruder using the optimum parameters. The influence of the coagent, triaUyl cyanurate (TAC), on the cross linking of low density polyethylene in the presence of peroxide was also investigated. The peroxide crosslinking was found to improve the mechanical properties and the thermal stability of the polyethylenes. The efficiency of crosslinking was found to be improved by the addition of coagent such as TAC.The optimum conditions for silane grafting viz temperature, shear rate, silane and DCP concentrations were determined on a torque rheometer in the case of LDPE, LLDPE and their blend. Silane grafting of LDPE in the presence of peroxide was performed with and without addition of water. Compounding of such mixtures in the melt at high temperatures caused decomposition of the peroxide and grafting of alkoxy silyl groups to the polyethylene chains.The optimum parameters for maleic anhydride modification of LDPE, LLDPE and their blend were determined. The grafting reaction was confinned by FTIR spectroscopy. Modification of polyethylenes with maleic anhydride in the presence of dicumyl peroxide was found to be useful in improving mechanical properties. The improvement was found to be mainly due to the grafting of carboxyl group and formation of crosslinks between the chains. The cross linking initiated improvements indicate extended property profiles and new application fields for polyethylenes.On the whole the study shows that the optimum conditions for modifying polyethylenes can be determined on a torque rheometer and actual modification can be performed in a single screw extruder by employing the optimum parameters for improved mechanical! thermal behaviour without seriously affecting their processing behaviour. |
Description: | Department of Polymer Science and Rubber Technology, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/2299 |
Files | Size |
---|---|
Dyuthi-T0591.pdf | (4.213Mb) |
Abstract: | The present work focuses on the modification of the commonly used thermoplastics, polypropylene and polystyrene using nanosilica preparcd from a cheap source of sodium silicate. Melt compounding technique has been used for nanocomposite preparation as it is simple and suited to injection moulding. Nanosilica in a polymer matrix provide significant enhancement in strength, stiffness and impact strength. Incorporation of silica particles in a polymer also improves its thennal stability. To achieve better dispersion of fillers in polymer matrices the mixing was done at different shear rates. The enhancement in material properties indicates that at higher shear rates there is greater interaction between particles and the matrix and it depends on filler concentration and type of polymer used. N anosilica is a useful filler in thennoplastic polymers and has been applied in automotive applications, electronic appliances and consumer goods.This thesis is divided into six chapters. General introduction to the topic is described in chapter 1. Salient features of polymer nanocomposites, their synthesis, properties and applications are presented. A review of relevant literature and the scope and objectives are also mentioned in this chapter.The materials used and the vanous experimental method and techniques employed in the study are described in chapter 2. Preparation of nanocomposites by melt blending using Thenno Haake Rheocord, preparation of samples, evaluation of mechanical and thennal properties using UTM, Impact testing and characterization using DMA, TGA and DSC and morphology by SEM are described.The preparation of nanosilica from a laboratory scale to a pilot plant scale is described in chapter 3. Generation of surface modified silica, evaluation of kinetic parameters of the synthesis reaction, scale up of the reactor and modeling of the reactor are also dealt with in this chapter.The modification of the commodity thennoplastic, Polypropylene using nanosilica is described in chapter 4. Preparation of PP/silica nanocomposites, evaluation of mechanical properties, thermal and crystallization characteristics, water absorption and ageing resistance studies are also presented.The modification of Polystyrene using synthesized nanosilica IS described in chapter 5. The method of preparation of PS/silica nanocomposites, evaluation of mechanical properties (static and dynamic), thermal properties melt flow characteristics using Haake Rheocord, water absorption and ageing resistance of these nanocomposites are studied. |
Description: | Department of Polymer Science and Rubber Technology, Ccchin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/2545 |
Files | Size |
---|---|
Dyuthi-T0689.pdf | (11.04Mb) |
Abstract: | Upgrading two widely used standard plastics, polypropylene (PP) and high density polyethylene (HDPE), and generating a variety of useful engineering materials based on these blends have been the main objective of this study. Upgradation was effected by using nanomodifiers and/or fibrous modifiers. PP and HDPE were selected for modification due to their attractive inherent properties and wide spectrum of use. Blending is the engineered method of producing new materials with tailor made properties. It has the advantages of both the materials. PP has high tensile and flexural strength and the HDPE acts as an impact modifier in the resultant blend. Hence an optimized blend of PP and HDPE was selected as the matrix material for upgradation. Nanokaolinite clay and E-glass fibre were chosen for modifying PP/HDPE blend. As the first stage of the work, the mechanical, thermal, morphological, rheological, dynamic mechanical and crystallization characteristics of the polymer nanocomposites prepared with PP/HDPE blend and different surface modified nanokaolinite clay were analyzed. As the second stage of the work, the effect of simultaneous inclusion of nanokaolinite clay (both N100A and N100) and short glass fibres are investigated. The presence of nanofiller has increased the properties of hybrid composites to a greater extent than micro composites. As the last stage, micromechanical modeling of both nano and hybrid A composite is carried out to analyze the behavior of the composite under load bearing conditions. These theoretical analyses indicate that the polymer-nanoclay interfacial characteristics partially converge to a state of perfect interfacial bonding (Takayanagi model) with an iso-stress (Reuss IROM) response. In the case of hybrid composites the experimental data follows the trend of Halpin-Tsai model. This implies that matrix and filler experience varying amount of strain and interfacial adhesion between filler and matrix and also between the two fillers which play a vital role in determining the modulus of the hybrid composites.A significant observation from this study is that the requirement of higher fibre loading for efficient reinforcement of polymers can be substantially reduced by the presence of nanofiller together with much lower fibre content in the composite. Hybrid composites with both nanokaolinite clay and micron sized E-glass fibre as reinforcements in PP/HDPE matrix will generate a novel class of high performance, cost effective engineering material. |
URI: | http://dyuthi.cusat.ac.in/purl/4981 |
Files | Size |
---|---|
Dyuthi-T2052.pdf | (26.71Mb) |
URI: | http://dyuthi.cusat.ac.in/purl/4982 |
Files | Size |
---|---|
Dyuthi-T2053.pdf | (9.608Mb) |
Abstract: | The present study was undertaken to prepare nanosilica by a simple cost effective means and to use it as a potential nanomodifier in thermoplastic matrices and to develop useful composites. Nanosilica was prepared from sodium silicate and dilute hydrochloric acid by polymer induced crystallization technique under controlled conditions. The silica surface was modified by silane coupling agent to decrease the agglomeration and thus to increase the reinforcement with polymer. The pristine nanosilica and modified nanosilica were used to make nano-micro hybrid composites. Short glass fibres and nylon fibres were used as microfillers. The hybrid nanocomposites based on Polypropylene (PP) and High density poly ethylene (HOPE) are prepared. The mechanical, thermal, crystallization and dynamic mechanical properties of the composites are evaluated. |
Description: | Dept. of Polymer Science and Rubber Technology, Cochin University of Science and technology |
URI: | http://dyuthi.cusat.ac.in/purl/2432 |
Files | Size |
---|---|
Dyuthi-T0659.pdf | (7.683Mb) |
URI: | http://dyuthi.cusat.ac.in/purl/5006 |
Files | Size |
---|---|
Dyuthi-T2073.pdf | (4.982Mb) |
Abstract: | With the advent of satellite communication and radio astronomy, the need for large and efficient reflector antennas had triggered a widespread investigation in reflector feed design techniques. Major improvements sought are reduction in spill-over, cross polarization losses and the enhancement of aperture efficiency. The search for such a feed culminated in the corrugated horn. The main idea behind the present work is to use the H-plane sectoral horns fitted with,corrugated flanges as feeds of a paraboloid and see how the secondary pattern of the reflector antenna varies with different parameters of the feed. An offset paraboloid is used as the secondary reflector in order to avoid the adverse effect of aperture ‘blocking by the feed horn structure on the secondary radiation pattern. The measurements were repeated for three different H-plane sectoral horns with the same set of corrugated flanges at various X-band frequencies. The following parameters of the whole system are studied: (a) Beam shaping. (b) Gain. (c) Variation of VSWR and (d) Cross polarization |
Description: | Department of Physics, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/3293 |
Files | Size |
---|---|
Dyuthi-T1261.pdf | (16.59Mb) |
URI: | http://dyuthi.cusat.ac.in/purl/1104 |
Files | Size |
---|---|
Pravinkumar P A 1985.pdf | (1.883Mb) |
Abstract: | This thesis investigated the potential use of Linear Predictive Coding in speech communication applications. A Modified Block Adaptive Predictive Coder is developed, which reduces the computational burden and complexity without sacrificing the speech quality, as compared to the conventional adaptive predictive coding (APC) system. For this, changes in the evaluation methods have been evolved. This method is as different from the usual APC system in that the difference between the true and the predicted value is not transmitted. This allows the replacement of the high order predictor in the transmitter section of a predictive coding system, by a simple delay unit, which makes the transmitter quite simple. Also, the block length used in the processing of the speech signal is adjusted relative to the pitch period of the signal being processed rather than choosing a constant length as hitherto done by other researchers. The efficiency of the newly proposed coder has been supported with results of computer simulation using real speech data. Three methods for voiced/unvoiced/silent/transition classification have been presented. The first one is based on energy, zerocrossing rate and the periodicity of the waveform. The second method uses normalised correlation coefficient as the main parameter, while the third method utilizes a pitch-dependent correlation factor. The third algorithm which gives the minimum error probability has been chosen in a later chapter to design the modified coder The thesis also presents a comparazive study beh-cm the autocorrelation and the covariance methods used in the evaluaiicn of the predictor parameters. It has been proved that the azztocorrelation method is superior to the covariance method with respect to the filter stabf-it)‘ and also in an SNR sense, though the increase in gain is only small. The Modified Block Adaptive Coder applies a switching from pitch precitzion to spectrum prediction when the speech segment changes from a voiced or transition region to an unvoiced region. The experiments cont;-:ted in coding, transmission and simulation, used speech samples from .\£=_‘ajr2_1a:r1 and English phrases. Proposal for a speaker reecgnifion syste: and a phoneme identification system has also been outlized towards the end of the thesis. |
Description: | Department of Electronics, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/3732 |
Files | Size |
---|---|
Dyuthi-T1697.pdf | (3.329Mb) |
Abstract: | Most living organisms are constantly exposed to potentially harmful pathogens. It is the immune system of the organism that enables it to survive in an environment loaded with dangerous pathogenic microorganisms. The innate immunity provides organisms with a rapid and non-specific first line of defense against pathogens. It includes physical barriers such as skin and mucous membranes and chemical barriers including the high acidity of gastric juice, and specialized soluble molecules that possess antimicrobial activity. One of the well-known innate immune defense mechanisms is the production of antimicrobial substances by specific cells or tissues of the organisms. Antimicrobial peptides (AMPs) are such natural substances that |
URI: | http://dyuthi.cusat.ac.in/purl/5084 |
Files | Size |
---|---|
Dyuthi- T 2150.pdf.pdf | (23.06Mb) |
URI: | http://dyuthi.cusat.ac.in/purl/5268 |
Files | Size |
---|---|
Dyuthi T-2304.pdf | (12.13Mb) |
Abstract: | Antimicrobial peptides (AMPs) are gene encoded, small sized, generally cationic, amphiphathic peptides characterized by antimicrobial activity against bacteria, fungi, viruses and other pathogens. They are a major component of the innate immune defense system of almost all living organisms, ranging from bacteria to humans and represent the first line of defense against the invading microbial pathogens (Boman, 1995; Zasloff, 2002). Antimicrobial peptides represent a heterogeneous group displaying multiple modes of action that are determined by the sequence and concentration of peptides. Their remarkable specificity for prokaryotes with low toxicity for eukaryotic cells has favored their investigation and exploitation as new antibiotics |
URI: | http://dyuthi.cusat.ac.in/purl/5089 |
Files | Size |
---|---|
Dyuthi-T 2155.pdf.pdf | (13.24Mb) |
Abstract: | The present study focuses on vibrios especially Vibrio harveyi isolated from shrimp (P. monodon) larval production systems from both east and west coasts during times of mortality. A comprehensive approach has been made to work out their systematics through numerical taxonomy and group them based on RAPD profiling and to segregate the virulent from non- virulent isolates based on the presence of virulent genes as well as their phenotypic expression. The information gathered has helped to develop a simple scheme of identification based on phenotypic characters and segregate the virulent from non virulent strains of V. harveyi. |
Description: | National Centre for Aquatic Animal Health Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/3697 |
Files | Size |
---|---|
Dyuthi-T1662.pdf | (11.04Mb) |
Abstract: | This thesis covers various aspects of viral diseases affecting shrimp aquaculture. The research component of this thesis can be divided into four areas. The areas covered are: I) A study to determine the prevalence of WSSV among the crustaceans in the Vembanad estuary, the shrimp aquaculture farms surrounding the estuary, and the sea off Cochin coast, India using two , sets of nested PCR primers. 2) An investigation to compare the sequence of six major structural proteins of WSSV; vp28, vp26, vp 19, vp68, vp281, vp466 from different geographical locations with that of an isolate from India. 3) Simultaneous occurrence of HPV, IHHNV, MBV and WSSV in postlarvae of P. monodon from hatcheries in India was monitored by Polymerase Chain Reaction. 4) A real time PCR procedure was developed for the quantitative analysis of WSSV infection. The viral load of postlarvae from hatcheries in Kerala meant for aquaculture was also determined using the quantitative PCR. |
URI: | http://dyuthi.cusat.ac.in/purl/2655 |
Files | Size |
---|---|
Dyuthi-T0711.pdf | (8.213Mb) |
Abstract: | The forms of natural rubber studied were sheet [RSS 4 and RSS 5], ISNR 20 and EBC. In the case of the latter two forms samples from estate and nonestate sectors were included. The samples were collected from different locations at specified intervals, for a particular period. The effect of the extent of mastication on raw rubber properties as well as the properties of the compounds and vulcanizates also studied. The consistency in raw rubber properties and breakdown behavior of skim rubber were studied by collecting samples periodically from selected processing units. The effect of incorporation of skim with ISNR 20 has also been investigated |
Description: | Rubber Research Institute of India Rubber Board, Kottayam |
URI: | http://dyuthi.cusat.ac.in/purl/3510 |
Files | Size |
---|---|
Dyuthi-T1460.pdf | (2.617Mb) |
Abstract: | The constitutive production of AMPs in shrimps ensures that animals are able to protect themselves from low-level assaults by pathogens present in the environment. As these molecules play important roles in the shrimp immune defense system, the expression level of these AMPs are possible indicators of the immune state of shrimps. The present study also indicates the antiviral property of AMPs, especially ALF, stressing the importance of their up-regulation through the application of immunostimulants/probiotics as a prophylactic strategy in aquaculture. The present study shows that shrimp defense system is equipped enough to evade WSSV infection to a certain extent, when the animals were maintained on marine yeast and probiotic diet, whereas the control diet fed group succumbed to WSSV infection. This study reveals that marine yeast and probiotic supplemented diet can delay the process of WSSV infection and confer greater protection to the animals. Particularly, the protection conferred by marine yeast, C. haemulonii S27 and Bacillus MCCB101 were highly promising imparting greater hope to the aquaculture community to overcome the prevailing disease problems in aquaculture. It may be inferred from the present study that up-regulation of AMP genes could be effected by the application of immunostimulants and probiotics. Also, AMP expression profile could be used as an effective tool for screening immunostimulants and probiotics for application in shrimp culture. Ultimately, it is likely that no single compound or strategy will provide a solution to the problem of disease within aquaculture and that, in reality, a suite of techniques will be required including the manipulation of the rearing environment, addition of probionts as a matter of routine during culture, and the use of immunostimulants and other supplements during vulnerable growth phases. Finally, the development of good management practices, the control of environmental variables, genetic improvement in the penaeid species, understanding of host-virus interaction, modulation of the shrimp immune system, supported by functional genomics and proteomics of this crustacean, as a whole suggests that the control of WSSV is not far. |
Description: | Department of Marine Biology, Microbiology and Biochemistry, School of Marine Sciences, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/2779 |
Files | Size |
---|---|
Dyuthi-T0802.pdf | (25.84Mb) |
Description: | Department of Biotechnology, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/2800 |
Files | Size |
---|---|
Dyuthi-T0821.pdf | (9.003Mb) |
Abstract: | In the present study diversity of E. coli in the water samples of Cochin estuary were studied for a period of 3 years ranging from January 2010- December 2012. The stations were selected based on the closeness to satellite townships and waste input. Two of the stations (Chitoor and Thevara) were fixed upstream, two in the central part of the estuary namely Bolgatty and Off Marine Science Jetty, and one at the Barmouth. Diversity was assessed in terms of serotypes, phylogenetic groups and genotypes. Two groups of seafood samples such as fish and shellfish collected from the Cochin estuary were used for isolation of E. coli. One hundred clinical E. coli isolates were collected from one public health centre, one hospital and five medical labs in and around Cochin City, Kerala. From our results it was clear that pathogen cycling is occurring through food, water and clinical sources. Pathogen cycling through food is very common and fish and shellfish that harbour these strains might pose potential health risk to consumer. Estuarine environment is a melting pot for various kinds of wastes, both organic and inorganic. Mixing up of waste water from various sources such as domestic, industries, hospitals and sewage released into these water bodies resulting in the co-existence of E. coli from various sources thus offering a conducive environment for horizontal gene transfer. Opportunistic pathogens might acquire genes for drug resistance and virulence turning them to potential pathogens. Prevalence of ExPEC in the Cochin estuary, pose threat to people who use this water for fishing and recreation. Food chain also plays an important role in the transit of virulence genes from the environments to the human. Antibiotic resistant E. coli are widespread in estuarine water, seafood and clinical samples, for reasons well known such as indiscriminate use of antibiotics in animal production systems, aquaculture and human medicine. Since the waste water from these sources entering the estuary provides selection pressure to drug resistant mutants in the environment. It is high time that the authorities concerned should put systems in place for monitoring and enforcement to curb such activities. Microbial contamination can limit people’s enjoyment of coastal waters for contact recreation or shellfish-gathering. E. coli can make people sick if they are present in high levels in water used for contact recreation or shellfish gathering. When feeding, shellfish can filter large volumes of seawater, so any microorganisms present in the water become accumulated and concentrated in the shellfish flesh. If E. coli contaminated shellfish are consumed the impact to human health includes gastroenteritis, urinary tract infections (UTIs), and bacteraemia. In conclusion, the high prevalence of various pathogenic serotypes and phylogenetic groups, multidrug-resistance, and virulence factor genes detected among E. coli isolates from stations close to Cochin city is a matter of concern, since there is a large reservoir of antibiotic resistance genes and virulence traits within the community, and that the resistance genes and plasmid-encoded genes for virulence were easily transferable to other strains. Given the severity of the clinical manifestations of the disease in humans and the inability and/or the potential risks of antibiotic administration for treatment, it appears that the most direct and effective measure towards prevention of STEC and ExPEC infections in humans and ensuring public health may be considered as a priority. |
URI: | http://dyuthi.cusat.ac.in/purl/4993 |
Files | Size |
---|---|
Dyuthi-T2062.pdf | (22.27Mb) |
Dyuthi Digital Repository Copyright © 2007-2011 Cochin University of Science and Technology. Items in Dyuthi are protected by copyright, with all rights reserved, unless otherwise indicated.