| Abstract: | Welding of high strength and low weight materials like Aluminium Alloys without any defects by conventional welding techniques is a major challenge in industries. Hence research on solid state welding techniques like Friction stir welding and Friction welding techniques have got much importance in joining of Aluminium alloys. However most of the industries are not changing conventional techniques as skilled workers are available on that area. Most common conventional welding techniques used for joining of Aluminium alloys are Gas welding and Arc welding. Friction welding is a solid-state welding process that generates heat through mechanical friction between a moving and a stationary component with the addition of a lateral force called “upset” to plast ically displace and fuse the materials. In this work, experimental study on tensile and micro structural characteristics of welded joints formed from conventional welding techniques and Rotary friction welding(suitable for weld specimens with circular cross section) has been carried out and the same were compared. The process parameters for arc welding used was 50-70 Amp reverse polarity DC and electrodes of 2.3mm diameter. In Gas welding, the parameters were oxy acetylene neural flame at 3200°C and 3mm electrodes . In the case of friction welding an axial pressure loading of 3Mpa with 5 MPa as upsetting pressure and 500 rpm were used to obtain good welded joints. Tensile characteristic studies of Arc welded joints and Gas welded joints showed 48% and 60 % variations respectively from the maximum load bearing characteristics of parent metal. In the case of friction welded joint, the variation was found to 46%. Micro structural evaluation of conventionally welded joints exhibited clear distinct zones of various weld regions. In the case of friction welded joint micro structural photographs showed comparable features both in parent metal and welded region. Thus the tensile characteristic study and microstructure evaluations proved that friction welded joints are good in both aspects compared to conventionally welded joints. |
| Description: | International Journal of Innovative Research in Science, Engineering and Technology,Volume 2, Special Issue 1, December 2013 |
| URI: | http://dyuthi.cusat.ac.in/purl/4677 |
| Files | Size |
|---|---|
| A Comparative S ... f Aluminium Alloy 6061.pdf | (704.1Kb) |
| Abstract: | HINDI |
| Description: | Department of Hindi. Cochin University of Science & Technology |
| URI: | http://dyuthi.cusat.ac.in/purl/4867 |
| Files | Size |
|---|---|
| Dyuthi-T1965.pdf | (7.994Mb) |
| Abstract: | HINDI |
| Description: | Department of Hindi Dean. Faculty of Humanities,CUSAT |
| URI: | http://dyuthi.cusat.ac.in/purl/4886 |
| Files | Size |
|---|---|
| Dyuthi-T1984.pdf | (11.99Mb) |
| Abstract: | This thesis is an attempt to make a comparative study of the composition of the muscle proteins of some commercially important species of fishes and shell fishes of our coast and their changes during preservation and processing. As a part of this the distribution of the major protein nitrogen fractions in several species of fishes and shell fishes was studied in detail. |
| Description: | Central Institute of Fisheries Technology |
| URI: | http://dyuthi.cusat.ac.in/purl/3594 |
| Files | Size |
|---|---|
| Dyuthi-T1532.pdf | (7.562Mb) |
| Abstract: | For improving agricultural marketing, which has been discussed in the previous chapter, the Government has intervened in different ways. The direct regulatory role through the regulation of markets and market practices is one of the ways in which governmental intervention can improve agricultural marketing. This study is an enquiry of the direct regulatory role of the government through regulation of markets and market practices. By restructuring the operational methods and redesigning the existing physical markets, this system gives direct benefit to the cultivating class and protects them from the market manipulations of organised and powerful private traders. If traders do not continue their trade for the time being they will not be affected financially, because they are resourceful or financially solvent. On the other hand, Cultivators must sell their produce immediately after harvesting for the lack of additional facilities or to satisfy other needs for which finance is required. Another important reason is that Cultivators/farmers are not organised and because of lack of their organisation, they sell their produces individually. In this situation, a farmer is helpless when astute traders indulge in manipulations at the time of purchase of the produces. So it is the government's obligation to protect the interest of the farmers. Protection of the farmer/cultivator is necessary not only from the point of social justice but also from that of economic growth. If the farmers are assured of a remunerative or incentive price for their produce, they will get the inspiration to produce more and through more production, economy will be developed and the nation as a whole will be benefitted. This study will examine the management system of the markets through the direct regulatory role played by the governments to control markets and market practices in West Bengal and Bangladesh. |
| Description: | School Of Management Studies, Cochin University Of Science And Technology |
| URI: | http://dyuthi.cusat.ac.in/purl/3435 |
| Files | Size |
|---|---|
| Dyuthi-T1415.pdf | (13.08Mb) |
| URI: | http://dyuthi.cusat.ac.in/purl/1299 |
| Files | Size |
|---|---|
| Usharani G 1988.PDF | (116.8Kb) |
| Abstract: | Speech is a natural mode of communication for people and speech recognition is an intensive area of research due to its versatile applications. This paper presents a comparative study of various feature extraction methods based on wavelets for recognizing isolated spoken words. Isolated words from Malayalam, one of the four major Dravidian languages of southern India are chosen for recognition. This work includes two speech recognition methods. First one is a hybrid approach with Discrete Wavelet Transforms and Artificial Neural Networks and the second method uses a combination of Wavelet Packet Decomposition and Artificial Neural Networks. Features are extracted by using Discrete Wavelet Transforms (DWT) and Wavelet Packet Decomposition (WPD). Training, testing and pattern recognition are performed using Artificial Neural Networks (ANN). The proposed method is implemented for 50 speakers uttering 20 isolated words each. The experimental results obtained show the efficiency of these techniques in recognizing speech |
| URI: | http://dyuthi.cusat.ac.in/purl/3912 |
| Files | Size |
|---|---|
| A Comparative S ... Isolated Spoken Words.pdf | (342.6Kb) |
| Abstract: | The catalyst compositions of the Zn1−xCOxFe2O4 (x= 0, 0.2, 0.5, 0.8 and 1.0) spiel series possessing ‘x’ values, x less than or equal to 0.5, are unique for selective N-monomethylation of aniline using methanol as the alkylating agent. Since dimethyl carbonate (DMC) is another potential non-toxic alkylating agent, alkylation of aniline was investigated over various Zn–Co ferrites using DMC as the alkylating agent. The merits and demerits of the two alkylating agents are compared. Catalytic activity followed a similar trend with respect to the composition of the ferrospinel systems. DMC is active at comparatively low temperature, where methanol shows only mild activity. However, on the selectivity basis, DMC as an alkylating agent could not compete with methanol, since the former gave appreciable amounts of N,N-dimethylaniline (NNDMA) even at low temperature where methanol gave nearly 99% N-methylaniline (NMA) selectivity. As in the case of methanol, DMC also did not give any C-alkylated products. |
| URI: | http://dyuthi.cusat.ac.in/purl/2244 |
| Files | Size |
|---|---|
| Dyuthi-SS42.pdf | (158.0Kb) |
| Abstract: | A comparative study on the anisole methylation with methanol over lanthanum-promoted Sn02 catalyst and its sulfate-doped analogue is presented. A maximum 2.6-xylenol selectivity of 82% was achieved at 400 degreeC under optimized conditions at an anisole conversion of 65% over lanthanum-promoted Sn02 catalyst. The sulfate modification resulted in the dealkylation of anisole to phenol followed by several unselective side reactions due to the creation of strong acid sites. The activity of lanthanum-modified tin oxide catalysts in the selective formation of 2.6-xylenol is ascribed to the presence of weak Lewis acid sites and comparatively stronger basic sites. |
| URI: | http://dyuthi.cusat.ac.in/purl/2170 |
| Files | Size |
|---|---|
| Dyuthi-SS10.pdf | (241.3Kb) |
| Abstract: | HINDI |
| Description: | DEPARTMENT OF HINDI COCHIN UNIVERSITY OF SCIENCE AND TECHNOLOGY |
| URI: | http://dyuthi.cusat.ac.in/purl/4824 |
| Files | Size |
|---|---|
| Dyuthi-T1921.pdf | (12.20Mb) |
| Abstract: | Hindi |
| Description: | Department of Hindi,CUSAT |
| URI: | http://dyuthi.cusat.ac.in/purl/4778 |
| Files | Size |
|---|---|
| Dyuthi-T1875.pdf | (8.406Mb) |
| Abstract: | In this paper, microstrip lines magnetically coupled to splitring resonators (SRRs) are conquved to electromagnetic bundgup (EBG) nr,rrostrip lines in terns q/ their stop-heard penjbrnmrnce and dimensions. In bath types o/ trunsmis•siou lines, signal propagation is inhibited in it certain jequency bwuL For EBG microstrip lines, the central frequency of such a forbidden band is determined by the period of the structure, whereas in SRR-hased microstrip lines the position of the frequency gap depends on the quasi-static resonant frequency of the rings. The main relevant conrributiun of this paper is to provide a tuning procedure to control the gap width in SRR microstrip lines, and to show that by using SRRs, device dimensions ale much smaller than those required by EBGs in order to obtain similar stop-banal performance. This has been demonstrated by fill-wave electromagnetic simulations and experimentally verified from the characterization ql two fabricated microstrip lines: one with rectangular SRRs etched on the upper substrate side, and the other with a periodic perturbation cf'strip width. For similar rejection and 1-(;H,. gap width centered at 4.5 Gllz, it has been found that the SRR microstrip line is•,fve times shorter. In addition, no ripple is appreciable in the allowed band for the .SRR-hared structure, whereas due to dispersion, certain mismatch is expected in the EBG prototype. Due to the high-frequency selectivity, controllable gap width, and small dimensions, it is believed that SRR coupled to planar transmission lines can have an actual impact on the design of stop-band filters compatible with planar technology, and can be an alternative to present solutions based on distributed approaches or EBG |
| URI: | http://dyuthi.cusat.ac.in/purl/1421 |
| Files | Size |
|---|---|
| Comparison of e ... s stop band structures.PDF | (686.9Kb) |
| Abstract: | Microwave properties of conductive polymers is crucial because of their wide areas of applications such as coating in reflector antennas, coating in electronic equipments, firequenry selective .surfaces, EMI materials, satellite communication links, microchip antennas, and medical applications. This work involves a comparative study of dielectric properties of selected conducting polymers such as polyaniline. poly(3,4-eth),lenedio.syt2iophene), polvthiophene, polvpvrrole. and pohparaphenylene diazomethine (PPDA) in microwave and DC,fields. The inicrowave properties such as dielectric constant, dielectric loss. absorption coefficient, heating coefficient, skin depth, and conductivity in the microwave frequency (S hand), and DC fields were compared. PEDOT and polccuiiline were found to exhibit excellent properties in DC field and microwave frequencies, which make thein potential materials in many of the alorenientioned applications |
| URI: | http://dyuthi.cusat.ac.in/purl/804 |
| Files | Size |
|---|---|
| K.Lakshmi and o ... microwave....June2007.PDF | (4.073Mb) |
| Abstract: | This paper compares statistical technique of paraphrase identification to semantic technique of paraphrase identification. The statistical techniques used for comparison are word set and word-order based methods where as the semantic technique used is the WordNet similarity matrix method described by Stevenson and Fernando in [3]. |
| Description: | 2012 International Conference on Data Science & Engineering (ICDSE) |
| URI: | http://dyuthi.cusat.ac.in/purl/4109 |
| Files | Size |
|---|---|
| Comparison of S ... aphrase Identification.pdf | (88.92Kb) |
| Abstract: | In this paper, a comparison study among three neuralnetwork algorithms for the synthesis of array patterns is presented. The neural networks are used to estimate the array elements' excitations for an arbitrary pattern. The architecture of the neural networks is discussed and simulation results are presented. Two new neural networks, based on radial basis functions (RBFs) and wavelet neural networks (WNNs), are introduced. The proposed networks offer a more efficient synthesis procedure, as compared to other available techniques |
| URI: | http://dyuthi.cusat.ac.in/purl/1413 |
| Files | Size |
|---|---|
| Comparison stud ... using neural networks.PDF | (379.2Kb) |
| Abstract: | The present study aims at the preparation of an ABS (acrylonitrile-butadiene-styrene) type toughened thermoplastic by melt blending polystyrene (PS) and powdered nitrile rubber (NBR). The product is an interesting class of toughened thermoplastic, which would combine the superior mechanical and processing characteristics of PS and the excellent oil-resistant properties of NBR. In this thesis an attempt has been made to investigate systematically the effect of compatibilisation and dynamic vulcanisation on the morphology and properties of powdered nitrile rubber toughened polystyrene. |
| Description: | Department of Polymer Science and Rubber Technology, Cochin University of Science and Technology |
| URI: | http://dyuthi.cusat.ac.in/purl/2542 |
| Files | Size |
|---|---|
| Dyuthi-T0686.pdf | (8.037Mb) |
| Abstract: | The principal objective of this study was to explore the compatibility of a blend of two synthetic elastomers viz., ethylene-propylene-diene rubber (EPDM) and chlorobutyl rubber (CIIR). Various commercial grades of EPDM were blended with a specific grade of CIIR at different proportions. The mechanical properties such as tensile strength, tear strength, ageing resistance, etc. were studied. On the basis of the observed physical properties, two particular grades of EPDM were found to be compatible with CIIR. Differential scanning calorimetry and scanning electron microscopy confirmed the results. Chlorosulphonated polyethylene was added as a compatibilizing agent to overcome the phase separation of the other two incompatible grades of EPDM in blending with CIIR. The results revealed that the addition of compatibilizer greatly improves the compatibility and thereby the properties of the blends. |
| URI: | http://dyuthi.cusat.ac.in/xmlui/purl/2001 |
| Files | Size |
|---|---|
| Compatibility studies on....pdf | (403.3Kb) |
| Abstract: | This thesis Entitled compensation to workmen for industrial injuries.Evaluation of the different forms of liability for compensating industrial injuries makes it evident that the liability under the social insurance scheme is the most befitting one, as it eliminates the problem of evasion of liability by the employer by providing for sharing of liability. Liability for compensation under the workmen's Compensation Act, 1923 and the Employees' State Insurance Act, 1948 arises only in the case of accidents, arising in the course of and out of employment. Majority of the workers, covered by the workmen's Compensation Act, have supported lumpsum payment of compensation under the Act. It appears that workers are ignorant of the cemerits of lumpsum payment. So, the workers should be properly educated by the Inspectorate, proposed above, about the comparative advantages of periodical payments. It is suggested that the workmens Compensation Act, 1923 may be amended, imposing fee upon the parties for each adjournment. It is also suggested that provision may be made in the workmens Compensation Act, 1923 for the expeditious despatch of amendments of the Workmen's Compensation Act, 1923, the Workmens· Compensation Rules, 1924 and the Schedules, made from time to time, to the comrnissioners for workmens Compensation, This will help them mete out justice to an injured workman, as required by the changes in the law. The Employees' State Insurance Act, 1948 and the Rules may be amended, requiring the employers to provide the employees with necessary information, in the vernacular language, about the employment injury benefits available under the Employees' State Insurance Act, 1948 and the formalities for obtaining the same. This will help the illiterate employees, especially the casual ones, avail of employment injury benefits. Changes in the law, on the lines suggested above, are imperative to make the system of compensation for industrial injuries prove effective and beneficial to injured workmen. |
| Description: | Department of Law, Cochin University of Science and Technology |
| URI: | http://dyuthi.cusat.ac.in/purl/3156 |
| Files | Size |
|---|---|
| Dyuthi-T1130.pdf | (14.16Mb) |
| Abstract: | Bank switching in embedded processors having partitioned memory architecture results in code size as well as run time overhead. An algorithm and its application to assist the compiler in eliminating the redundant bank switching codes introduced and deciding the optimum data allocation to banked memory is presented in this work. A relation matrix formed for the memory bank state transition corresponding to each bank selection instruction is used for the detection of redundant codes. Data allocation to memory is done by considering all possible permutation of memory banks and combination of data. The compiler output corresponding to each data mapping scheme is subjected to a static machine code analysis which identifies the one with minimum number of bank switching codes. Even though the method is compiler independent, the algorithm utilizes certain architectural features of the target processor. A prototype based on PIC 16F87X microcontrollers is described. This method scales well into larger number of memory blocks and other architectures so that high performance compilers can integrate this technique for efficient code generation. The technique is illustrated with an example |
| Description: | International Journal of Software Engineering and Its Applications Vol. 6, No. 1, January, 2012 |
| URI: | http://dyuthi.cusat.ac.in/purl/4668 |
| Files | Size |
|---|---|
| A Compiler Inte ... ry Embedded Processors.pdf | (577.3Kb) |
Dyuthi Digital Repository Copyright © 2007-2011 Cochin University of Science and Technology. Items in Dyuthi are protected by copyright, with all rights reserved, unless otherwise indicated.